Jump to content
SAU Community

Recommended Posts

Hay Everyone,

I was just wondering if anyone knows if you can put an RB26dett engine and gear box, including the front wheel drive into an R33 GTST. Cause I was thinking of doing it......

HAs this been done before? Are the engine mounts the same? Will the GTST drive shaft fit and do you have to replace the diff?

I can't wait to here what you guys think.

Cheers

Gold Rays

Link to comment
https://www.sau.com.au/forums/topic/17541-rb26dett-in-a-r33-gtst/
Share on other sites

Ive seen an RB26DETT (without the 4wd stuff) in a 4 door R33 and it wasnt as easy as just swapping everything over. It took about three days for a mechanic who specialises in skylines to iron out all the little problems. i think electrics were more of a problem than mechanical. it had bigger turbos, a powerfc and avcr too. that being said, make sure you reasearch it first....

I'd say it would be cheaper in the long run to sell your GTSt and buy a GTR.. Otherwise pick up a GTS4 and drop an RB26 into that, then you have ATTESA...

A mate of mine has put an RB26 into his GTS, engine dyno'd at over 700hp, thing is an animal in the dry in any gear... I like the grip of my GTR :D

Brett

i don't bother me if I can't get the FWD. I want to do what your mate did.

I heard you could buy some sort of 4WD kit for a GTST!!!

I will be doing all the installing work with help of a few mechanics for free, so i don't have to worry about the cost of that. Only the cost of the front cut.

Another question: Is the GTR chasis the same as a GTST?

Hi Gold Rays, last time I priced a half cut R33 GTR it was close enough to $12K, to that you would need to add the cost of an R33 GTR tail shaft, rear diff, rear uprights, brakes, drive shafts, suspension arms, fuel tank, fuel pump, rear outer guards, rear inner guards, panel beating, painting etc etc

Someone already said it, "I'd say it would be cheaper in the long run to sell your GTSt and buy a GTR"

Plus in the end you would still have a GTST, not a real GTR.

My thoughts anyway

All RB block patterns are the same so it should just bolt straight in. Don't know about the 4WD though.

And 1989 R32 GTR's are going for about 15K in Jap land ATM so you may want to just upgrade. Check out prestige motorsports mailing list.

http://www.prestigemotorsport.com.au/au/st...asp?StockID=833

If the link don't work just sign up.

Guest YZF-R1 Maniac

Here are another couple from Prestige motors. I have been receiving their emails for a while and they are getting really cheap.

http://www.prestigemotorsport.com.au/au/st...asp?StockID=892

http://www.prestigemotorsport.com.au/au/st...asp?StockID=897

Is that you Damien??(TasGTR)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...