Jump to content
SAU Community

Recommended Posts

Hi!

My rb20 is playing on me. Yesterday I went for a drive.

Car was ok for pretty much whole time, normal driving, could boost etc.

Than I tried to have a speed test with s14 sr20det from.

Turned on my boostcontroller, installed recently. Profecb, tuned to 0.6-0.7 at 1,2,3 gear. Standing, 1,2,3(gave it some revs), go. 1 st gear pulling, 2nd gear car jurks, no boost. I stop immediately. Idle revs not stable, can't drive a car at all, no power under load. Checked all the hoses, seemed fine and in place. Vacuum at idle : -.7 bar, can rev but with some misfire around 2k.

Revs stable at idle.

Than I turned the engine off to let it rest for a bit. Turned on again in 10-15 min, same. Puffed some black smoke when I put in 1st gear and gave it some revs just to move. On the road home I had to built some revs, around 2-3 k and engage the clutch to make it drivable, without doing it it woulnd't built revs with WOT at all, just drop rev and stall.

Came home hooked up consult, no errors - code 55.

Unplugged AFM, 2500 limiter.

Here are some vids shot yesterday and today.

It was a bad idea to get out of the basement park with such problems, but had no choice, had to do it anyway.

Yesterday consult:

http://www.youtube.com/watch?v=Touv0v_TSko

http://www.youtube.com/watch?v=Krp-y-Fc8tA

Today revs under load, driving:

http://www.youtube.com/watch?v=E3Xf99kv0g0

http://www.youtube.com/watch?v=xxD_TbGoR5Q

http://www.youtube.com/watch?v=HGowIKq2JGw

http://www.youtube.com/watch?v=HGowIKq2JGw

http://www.youtube.com/watch?v=a1vcYxoasiU

http://www.youtube.com/watch?v=Wdu9lumNuuc

My ideas:

Fuel pump. (I have bosch 040, maybe it died ?) shows 2.5 bar at idle. Like it should.

AFM died ?

Timing belt jumped a tooth ?

.Sorry for my english LOL.

Looking forward for some ideas.

Thanks!

Edited by robots

I looked at all the piping and it seems to be all in place. If I understand correctly it won't idle ok and it won't show -.7 vacuum at idle. As no piping - leak, unregistered air is going in.

have u checked ur afm? also wat mods u got on the car? its hard to say when we dont know whats been done to it?

also black smoke could be a turbo? correct me if im wrong, but if you blow the turbo, the car will still run but no boost yeh? shot an exhaust wheel??

Edited by cheez

Mods: stock engine, fmic, stock exhaust, bosch 040 fuel pump.

I checked the intercooler piping and its seems intact. I will go have some fun with my car today. Maybe go get another AFM.

Edited by robots

Ok, I've managed to get my engine boosting and reving again. Problem was with the the pipe from the afm to turbo, air leak. And from intercooler to intake plenum. They all had air leaks once on load. Strange. Than after I get rid of that problem, car became driveable. But doesn't pull as hard as before. Didn't try with the boostcontroller yet. Also turbo now got that flatter sound. And I also get backfire when I change gears. I was like wtf ? Also there was some oil in the turbo>intercooler pipe. Cleaned it.

So now car boosts, has mad turbo flatter sound, doesn't pull as hard and gets some idle rev issue when u back of the throttle or press brakes.

Any ideas ?

Will post vids later.

Edited by robots

Boosting again.

http://www.youtube.com/watch?v=lTYpV9mc1bY

1st gear pull and really loud bang/backfire. It was like gun shot.

Had little fuel in the tank at that moment. So I had something like a fuel cut after that backfire. Damn it :x

http://www.youtube.com/watch?v=jC_ZxgPEe_c

Exhaust note at idle after the backfire bang.

Now I got some drone sound in the downpipe area. Maybe I shot of a turbo exhaust wheel ? :cheers: :?

http://www.youtube.com/watch?v=xyck4sARUe4

And some fun, doing some donuts a week ago.

http://www.youtube.com/watch?v=KFE8Xzy8wBU

What I got now:

1)Engine can rev, make boost.

2)Got mad turbo flatter sound now.

3)Got rid of most air leaks I guess.

4)Car doesn't pull as hard as before. Or I just forgot how it pulled already.

5)And I get backfire bangs nearly every time I change gear. It even backfires on idle, when I rev it and lift off the throttle.

When I was looking for the air leak in intercooler piping, I found some oil build up in turbo>intercooler pipe, wiped it off.

Edited by robots

I had oil all through my piping and exhaust when the seals in my turbo blew, so maybe that has happened.

Not too sure bout the backfiring but when my 32 was still N/A i had alot off backfires or 'pops' as i changed gear and some times when i changed down

The turbo flutter could be from a BOV that isnt opening and pushing out the air back through the turbo (oil in the piping might have gotten into the BOV and is making it harder for it to open). also if there is oil leaking through the inlet side and into the motor that may aslo be holding back some power, and not letting it feel like it is going as hard

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so will run the piping over that radiator and no plenum it is. Put that money towards a Haltech and see what suits. Any ideas something like an elite 2000 or 2500 right? My long term goal is 300kw e85 and manual swap and that’s a dream come true. For now will be 200kw and auto the stock rb25det neo intake isn’t too expensive with throttle body. If I was to have the port matching done, Would that be better than the stock de intake as the det has bigger holes plus has the spots for sensors etc? And suit more long term?  appreciate the advice?   
    • You understand AFR is not the only thing that contributes to it pinging yeah? Funnily, what the AFR gauge will tell you when it likely is pinging, is going to make you think things are really safe and good.
    • Run the piping how we all have for decades. Also the duel runners with the +T setup dramatically helps it gets on boost quicker. Yes, chase huge power it'll become a problem, but you're a long way off when you're already saying an aftermarket ECU is out of the budget. You also say NisTune as it's simple, and then immediately say it'll be painful, meaning... It won't be simple. It will likely cost you a lot more stuffing around with a Nistune, than just putting a Haltech or similar in.
    • I’ll order an afr gauge to keep an eye on it.  Then will get a haltech soon 
    • TD05 or maybe pulsar PSR2867r Gen 2?  id love a garret but it’s quite out the budget for now and I’m not chasing crazy power.    yeh fuel pump haven’t looked into but whatever works, kind of last on my list.    Nistune because it’s simple but Ik it’s a lot of pain especially as I’m auto +t with the whole seperate TCM etc still investigating that. Haltech id love but once budget tight for now atleast.    finally the reason I’m trying for a plenum instead of the stock intake is I already have a standard Intercooler mounted etc. so the ports are on both sides so trying to not have to go over the clutch fan radiator etc. trying to find a good deal return flow if I don’t than this will do for now I guess. btw any ideas with that, apparently some people have to cut blades to reduce it from hitting the Intercooler piping over the radiator ? Thanks 
×
×
  • Create New...