Jump to content
SAU Community

Rb20/25/vg30 Hydraulic Lifters

Cubes
 Share

Recommended Posts

  • 2 weeks later...
Cubes Grand Master

Cubes

Posted
  • Author
Posted

Sorry bud the boost controller is taken.

However,

I have seen this boost controller holding 18psi on a mates external gate GT35r .82 setup.

As for internal gate it held 17.5psi on my own and it dropped peak spool from ~4200rpm to 3300rpm but given the actuator is quite lazy cracking the flap off the seat way too early and too much. On the old stock turbo the spool improvement was very much noticeable.

I've decided on a programmable rpm vs boost controller as 19psi odd at 3300rpm isn't all that streetable.

Cubes Grand Master

Cubes

Posted
  • Author
Posted

4 x RB20/RB25 Knock sensors added.

2 were off a spare motor and the other 2 were off my own Rb20DET that were working fine when I had the RB20DET pfc on it.

The RB26 pfc uses different knock sensors so these are no good to me as the calibration is out.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • GTSBoy
      R34 25GT Engine Light 21

      By GTSBoy · Posted

      If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • The Bogan
      SAU NSW - R U OK? Southern Highlands Cruise

      By The Bogan · Posted

      Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...