Jump to content
SAU Community

Need Advice

18RZZ

By 18RZZ,
in Queensland

 Share

Recommended Posts

Oblivion Grand Master

Oblivion

Posted
Posted
well most of you guys saw my car on sunday i think the only thing going for it at the moment was the passenger in the car with me.

so as you all can see i need all the help i can get..

i did however notice that i am the only one without an exhaust system on my car so i think the first thuings i am going to do is the FMIC ( thanks to MARKIMARK performance ) and an exhaust. if the pipe work i make for my exhaust system does not work is there anyhhtaffer i good rane of decent systems (cat or turbo back )

lol

your was good as, at least you have a full front bar and no damage :(

i would go a 3" all the way through, dump pipe etc....metal cat if you want to stay legal and have no restriction. (metal cats are a fairly new product), i have one muffler in mine as well as the cat, other then that it is just straight through.(the muffler is the rear twin section)

  • 2 weeks later...
  • 2 years later...
lagperformance Contributor

lagperformance

Posted
Posted
Hey yall i bought my r32 a little while ago now and am looking to ypgrade the turbo but me being me i have no clue what will fit and what i need so i am hopeing you guys and gals can give me a hand.

Suggestions needed: TURBO, EXHAUST,EBC, COMPUTER, INJECTORS,FUEL PUMP, etc

i have already bought an apexi dyna flow front mount but need help putting it on LOL so useless says i. (hint hint markimark heard you are the man to show me how )

i am looking to get around the 200 - 220 RWKW mark but i dont want to be straining the engine to get the out of it.

Please help me

chipped factory ecu run gtr skyline injectors 440cc plenty of fuel for what your chasing, run a falcon throttle body, 3inch straight thru exhaust, external gate 38mm with screamer, to4e or gt28rs are both good options even a good rb25 turbo will do the trick, get a walboro intank fuel pump take yours out slot it in and a rising rate fuel pressure regulator should see the power your looking for piece of cake and an afm from a z32 300zx

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...