Jump to content
SAU Community

Recommended Posts

Hi all,

I've got a strange whistling noise which, from my perspective in the drivers seat, is coming from the front left of my car (1990, R31 4 door manual). All of my car savvy friends have had a drive/listen and have been unable to identify it, and I've also taken the car to 2 different mechanics, who were also unable to tell me what it was.

The noise is only there under a few specific conditions:

- in 3rd or 4th gear

- between 1500 and 2500 rpm

- travelling between 50 and 65km/h

- engine has to be reasonably cold or the outside temperature has to be cold, won't do it if it is a warm day or once the engine has warmed up.

If anyone has any idea what could be causing this noise, or if they've had a similar problem could you please reply here or email me at sticks_12@hotmail.com with any help it would be greatly appreciated.

Scy

Edited by Scy

what kind of intake system do you have IE standard intake box, pod filter??

have you have the r31 for long?

whisling nosie is generally an air leak but there is only the intake system in that corner, have you had any work done on the engine latly?

do you notice any thing different when you drive it??

just trying to get an idea...

Standard intake system, I haven't added or changed anything about the car since I got it.

I've had it for almost 2 years, and the noise has only just appeared in the last 3 or 4 months.

Only work I've had done it since I got it was getting a new radiator and clutch put in and I havent noticed any mechanical issues or changes in the way it runs/drives since the noise appeared.

my mate had a whistling sound coming from the front of his car after a front mount install (cheap one), and only between sertain speeds. from what we can tell must be the air going through the fins and whistling. you said you got a new radiator, is it a good quality one. might be the same thing but with your radiator fins. just an idea.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
    • Cheers mate. Seems some people get lucky others don't. It looks like the motor was detonating (to be expected if it was overboosting I suppose) as the pistons had a lot of detonation damage, and the bearings were stuffed. The bores were very scoured too, not sure if that's from the pistons or bits of ceramic turbo. By the by now. Have been trying to avoid the rabbit hole too much on the rebuild, and there's been a few hurdles along the way, but with any luck I'll have the car back soon™. Might even pop up a thread then.  
×
×
  • Create New...