Jump to content
SAU Community

Recommended Posts

Hey guys, at the moment im using the aerial cable as my earth for headunit, but now i want to use my aerial so where is the best nice and easy spot for new earth? I also want to run some of my guages to this earth also, Any ideas? Its for a R33 S2.

I have tried a couple spots around the bolts by the gearbox etc, no luck.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/188310-want-a-new-earth-for-headunit/
Share on other sites

Times three!

I sanded the metal ring part (after removal. Easy), stuck a bolt and washer over one hole, then sprayed the whole thing black gloss. Remove the bolt and washer, and you have a perfectly clean grounding point. Attach ground wire after re-installing it all and then spray or rub with some kind of lubricant (WD40, etc), which will stop the bare metal from rusting.

I tried the spot u three guys use, tested it with light n was ok the connected it up properly n for sum reason didnt work? I still duno y it didnt work.

Just to make sure we are talking about the same spot, one of the four bolts underneath the gearstick cover, beside the lower rubber part off stick?

make sure youve sanded back any paint that is at that point. bare metal is a good ground, paint is not :) by all means paint over it once grounded to stop rust. also make sure the ground wire from the head unit isnt dodgy. ive had one with a break in the ground wire before. would work randomly. replaced the ground wire at the plug - which wasnt fun :(

wire is all fine, dont think its an fuse problem as when i change back to my old earth it all good. Im really confused why when i test the point steve told me it shows its good, then I wire it up, none of the bolts can be earthed when i test with light. Its fine till i connected it lol. Then i take it off and that point is ok again :thumbsup:

I tried the spot u three guys use, tested it with light n was ok the connected it up properly n for sum reason didnt work? I still duno y it didnt work.

Just to make sure we are talking about the same spot, one of the four bolts underneath the gearstick cover, beside the lower rubber part off stick?

That quiet funny actually, because I wired up a head unit in my friends R32, and used the same grounding point as mine, which is the one were all referring too, and it didn't work either!

Very weird..

I just used one of the other screw holes that holds the rubber boot thing in place.

The mounting bracktes in the dash, to the left and right side of the head unit also work as an earth.

So i can use the earth point at the back of head unit then if i can earth to mounting brackets? I havent had a good look at it but i thought the brackets are all attached to plastic and not the body at all?

Yer... I probably wouldn't trust the brackets to be well grounded actually.

Failing the rubber boot surround bit, perhaps go for something around your handbrake? Removing the entire centre console at the point you are now is just a few extra screws.

Yea i had all that off aswell fitting switches in my console box. Il have a play around the handbreak in the weekend, I did try what Hellfire said at start but i had trouble geting dam footrest off, is there more than just 2 screws or what?

Also what is that thing underneath the console box? behind the handbreak a lil bit. Is that something to do with the airbags?

Oh i see, yea i took the front 2 off and couldnt get the footrest off so i tried hookin earthcable up to one of them bolts lol no gud, how does the foot rest come off? i used a bit of force but also didnt wana break it lol im gud at that haha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • In Vic it would be a defect regardless of whether or not you cut a hole in the sheetmetal for the return pipe. The rules in Vic are shitful, and are generally interpreted as you can "make 2 mods to the intake system". Putting an FFP and an FMI onto it will almost certainly be seen as some huge number of intake mods. You really need to speak to an engineer before doing this stuff in VIC.
    • planning a r34 rb25 de+t with some other work, rather just have it done in a shop due to space limitations any recommendations? I have most the parts already I seen online Moore Performance and DR Drift any advice appreciated thanks 
    • I’ve read the previous posts so just looking for latest information on how people have dealt with front facing plenum is it a defect etc or didn’t pass roadworthy or was it not noticed? Have a r34 and deciding if I should make a hole on the driver side or not.  I know some people have said blitz return flow but I might get rid of the stock intake down the line for a plenum so I rather set up for that now plus I already have a standard Intercooler. Car is mainly stock  Thanks. 
    • Actually, if having and keeping the stock ECU is the plan, the correct answer is to put Nistune into the ECU and improve the situation, not just look at it.
    • Wrong side of sydney for me coming from Goulburn, but you should head along, all ages of Skylines will be very welcome
×
×
  • Create New...