Jump to content
SAU Community

Recommended Posts

Hi Guys

Just wondering if any of you 34 owners would have the stock rear muffler that i could borrow to get this EPA of my car. I have put the standard Cat back exhasut on the car but being a nismo optioned car, it has the Nismo muffler on it and with this muffler on the cat back, its still 3Db over the limit :closedeyes:

Can anyone help me? Im willing to pick up and drop off

Thanks guys, (Im in the tullamarine area)

Link to comment
https://www.sau.com.au/forums/topic/189821-stock-r34gtt-rear-muffler-to-borrow/
Share on other sites

You blew 93dB @ 4700rpm with the stock exhaust and just a muffler?

jebus... :closedeyes:

I ran 94dB @ 5100rpm with twin 80mm dumps and 3.5" exhaust, that was using two mufflers and one cat :spam:

Cause RB26 is 400rpm higher test point than the RB25, i think you must have something a miss somewhere to be that lound!

Does it have one muffler or two?

Changing the mufflers to something a bit larger/better would most likely solve the problem on your aftermarket item, you might then not even need the factory one.

You blew 93dB @ 4700rpm with the stock exhaust and just a muffler?

jebus... :closedeyes:

I ran 94dB @ 5100rpm with twin 80mm dumps and 3.5" exhaust, that was using two mufflers and one cat :spam:

Cause RB26 is 400rpm higher test point than the RB25, i think you must have something a miss somewhere to be that lound!

Does it have one muffler or two?

Changing the mufflers to something a bit larger/better would most likely solve the problem on your aftermarket item, you might then not even need the factory one.

Blew a 93 with 3 "dump and 3"cat, stock cat back with genuine nismo muffler?? a stock muffler should shut it up a bit i hope

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...