Jump to content
SAU Community

Recommended Posts

hey guys, i was on a test drive today trying to sell my car and gave it a hit coming onto the highway and it kinda just seemed to have no go for a bit then just boosted big time and then a whole lot of white smoke came out the exhaust and the car shut off and i can't get it started again, i have had a blown engine before and this seems like the same thing as before, i found some pretty crunched up metal in the exhaust and was wondering if the turbo's blow does some of it get sucked through the engine as well causing it to blow the whole thing up or is it not starting just because the turbo's are stuffed. I have a power fc if that makes a difference, thought maybe it's a safety thing on it.

When i popped the bonnet i could smell oil but nothing was coming out under the engine and when i tried to start it again there was some smoke coming from the turbo area so i figured it might have blown the oil feed line off too but i couldn't get in there to look at it properly.

It's a GTS-T with an RB26 conversion.

Any help would be appreciated. Thanx.

Tom.

Link to comment
https://www.sau.com.au/forums/topic/192008-have-i-blown-my-engine/
Share on other sites

god i hope not or it'll be the second time i've blown a rb26 in about 5 months :rant: Plus i have a baby due in like 3 months, it'll take me ages to save up to fix it :down: If anyone wants to buy it for 10k it's still for sale :rofl: Good project even if you rip out the whole engine and put a new RB26 in there you'd get away with it for around 15k :P

you were a brave man putting in a second rb26 with ceramic wheeled turbos :(

Why didnt you change them when the motor was out?

'cause the guy i got to change them was a mechanic from my work and he reckoned that they came standard with steel wheels even though i told him a good 50 times that only the n1's came with steel wheels but he was positive the new rb26 he sourced me had them. I think he was pissed cause he grossly under quoted me to swap the engines over and he didn't want to do any more work than he had to haha

You said it wouldn't start--it won't turn over at all or it would actually start? If it won't even turn over, you just trashed a motor. Either pieces are wedged in the motor or you starved it of oil and it seized (if it won't turn over at all).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...