Jump to content
SAU Community

Recommended Posts

Hi all,

The head unit that came with my car was a Panasonic MRX777 (CD and mini disc in single din unit - http://www.minidisc.org/part_Panasonic_CQ-MRX777.html).

The whole thing lights up fine, playes radio stations etc, but when I insert a CD or a mini disc, it whirs for a bit, then says "E1" (disc error), ejects the CD and shuts down. :rolleyes:

Anyone have any ideas?????????? :)

Link to comment
https://www.sau.com.au/forums/topic/19201-pioneer-head-unit-problems/
Share on other sites

The head unit that came with my car (sony) did the same thing but only on some discs. Couldn't hack it so I changed head units. If you must keep this unit though try and find a car audio repairer or call / take it to panasonic (or pioneer).

hippy, JVC have a CD / MD single DIN as well.

Yeah, doh, meant Panasonic (changed now :D ).

When I say it 'whirs', I mean it sounds like it's reading the CD (just like my normal CD players do), but then it complains of the error. It does the same thing whether I'm using the MD or CD (even tried some 'made in Japan' CDs).

Guest purple_reign

sorry i just read your first post again.

most 'new' head units will have a transport screw in them that stops the carriage moving etc. when they are packaged up and shipped (well they used to when i was last installing). they are normally marked on the side or top of the unit saying 'transport screw remove before installation' (or has it in the manual, and normally have a small red head on them.

if it's already in the car (used) unit then i would suspect the laser assembly or something around that area. which would mean it needs to be taken to a repair agent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...