Jump to content
SAU Community

Recommended Posts

RICE DROP 12500 NEEDS EITHER NEW CLUTCH OR CLUTCH FORK

HEAPS OF SPARES EXCELLENT CONDITION CAR JUST CANT AFFORD TO KEEP IT WANT IT GONE

Make: Nissan

Model: Pulsar Gti-R

Milage: 147,000

Transmission: 5spd Manual

Colour: wrc blue

Location: Melbourne

RWC supplied? no

Currently registered? yes

Price: 14,000ono

Contact: Mick on 0431077303

Comments / Modifications:

comes with brand new and uninstalled

-engine hose overhaul kit

-clutch fork

-release bearing

-clutch fork pivot ball

INTERIOR

apexi boost guage, autometer a/f ratio guage, greddy turbo timer, battery relocated to boot, clutch

pedal support bracket, clean standard seats & trim

EXTERIOR

recent respray in WRC Blue with all new rubbers, 17" gmax rims, DBA front & rear slotted rotors,

clear side indicators

ENGINE & DRIVELINE

HYBRID FMIC w/heat wrapped cooler pipes, bosch 984 fuel pump, malpassi rising rate reg w/fuel

pressure guage, 3" full stainless exhaust, Magnaflow muffler, highflow cat, oil catch can, hks pod

filter, turbosmart duel stage boost controler, GFB blow off valve, xtreme lightened alluminium

flywheel, xtreme ceramic 9 puck xtra heavy duty clutch, spark plug cover, whiteline front strut

brace

FOLLOWING PARTS ARE LESS THAN 6000KLMS OLD

clutch fork boot, gearbox thrust bearing, chain tensioner, dizzy cap and rotor button, recon

front driveshafts, clutch slave cylinder, clutch master cylinder, water temp sensor, coolant temp

sensor

XTRAS (SPARES)

used lockwood white face dials, 1x set of arias forged pistons with rings, 2x cylinder heads, 1x

reground cams, 1x standard cams, 2x standard valves pring sets, 2x head bolt sets, 1xrocker

cover, 1x standard bore block, 1x 20thou bored block, 2x sumps, 2x oil pump timing cover

assembly, 2x conrod sets, inlet manifold with plenum, quad throttle bodies, fuel rail with standard

injectors, permaseal full gaskit kit, spare hatch with spoiler and glass, two front bars that need

minor repair, 1x rear bar, standard top mount intercooler, l/h indicator, l/h electric mirror, driver

side door with wind shield, right hand guard, air con condensor, pump and lines, gtir manual on cd,

tail shaft, box of bolts, wiring, bearings and other

stuff.

This car is extremely well maintained and has been serviced every 5000klms with motul oil.i wash

it every w/end and polish it with auto glym polish every 2nd. i always let it warm up before driving.

while i have owned it, best 1/4 mile time 13.121 on 13psi , currently has 172 kw atw on 15.5psi

with dyno sheets to prove, tuned a little rich to be safe so could gain a few extra kw by advancing

timing. good for a high 12 sec pass.

any test or inspection welcome

4months reg comes with the plates LILZLR

doesnt come with rwc but the car should pass easily enough

Images: post-44653-1195369493_thumb.jpg

post-44653-1195369752_thumb.jpg

Edited by LILZLR
  • 1 month later...

RICE DROP 14,000 FIRM NEEDS EITHER NEW CLUTCH OR CLUTCH FORK

HEAPS OF SPARES EXCELLENT CONDITION CAR JUST CANT AFFORD TO KEEP IT WANT IT GONE

CONTACT ME ON 0431077303 MICK

Edited by LILZLR
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • It's almost certainly a reluctor generating an "AC" waveform. No, ECUs don't generally read those - they're usually set up for PWM square wave 0-5v stuff.
    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
×
×
  • Create New...