Jump to content
SAU Community

Various Gtr Parts And General Bits

Risking
 Share

Recommended Posts

Risking Grand Master

Risking

Posted
Posted (edited)

Pair of Blitz pods with adaptors but no air flow meters. Very good condition, no rips or tears in the filters. $150

Blitzpods.jpg

Greddy Emanage Blue, As new condition, removed from a crashed vehicle, Supplied with injector loom but no ignition loom.

Comes with original box and manual etc $350

Emanage.jpg

4 Toyo R888's Done a few laps around wakefield from memory, Selling as I cant fit 16's over my Brake upgrade anymore. They are 16 by 225's (standard R33 tire size I think) 90% tread depth left still have paint marks

ToyoR888.jpg

Pair of Nismo 14411-06U00 Turbos. These are rated at 600ps and are pretty responsive as well. They require new thrust bearings as there is a bit of thrust movement but they still make boost and are not noisey at all. Im removing due to a GTRS upgrade so no longer needed. prefer you to inspect and negotiate appropriate price before purchasing.

Will post photos a bit latter on of the turbos

Pair of High flowed OEM turbos, done by precission turbos in 06' with steel wheels etc. They had made 290kw and were nice to drive with. Again they have thrust movement but were not noisey and boosted fine, No other bearing movement but should have the thrusts replaced and the rest checked obviously. Again rather you inspect them before negotiating a price thats fair.

All parts located in sydney and can organise postage for most items.

Edited by Risking
Link to comment
https://www.sau.com.au/forums/topic/199531-various-gtr-parts-and-general-bits/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • joshuaho96
      Automatic Power Button Light Flashing

      By joshuaho96 · Posted

      Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • BOLGE
      R34 Plug Identification

      By BOLGE · Posted

      Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...