Jump to content
SAU Community

Recommended Posts

check out this youtube video on the Varex Remote controll Muffler its bad quality video but

it shows you all about it, i am trying to get 1 now, i just dont know if it will hurt my exhaust valves or even my cat what do you guys think, the bypass makes me think it wont

Link to comment
https://www.sau.com.au/forums/topic/200754-varex-remote-control-muffler/
Share on other sites

check out this youtube video on the Varex Remote controll Muffler its bad quality video but

it shows you all about it, i am trying to get 1 now, i just dont know if it will hurt my exhaust valves or even my cat what do you guys think, the bypass makes me think it wont

That's pretty mad... I've got an APEXi ECV (standard butterfly valve) on my 33... lol well kinda! The idea was to hook it up to the motor that came factory with the car, but I've never gotten around to doing the cable.. so it's 100% open all the time! When I manually close it up (to about 90%... don't want it 100% blocked!) it's not too much different at idle/low revs but really noticeable at higher revs. I must note that i have a VERY LOUD exhaust on mine... only intensified by the fact that it's NA :D

That's pretty mad... I've got an APEXi ECV (standard butterfly valve) on my 33... lol well kinda! The idea was to hook it up to the motor that came factory with the car, but I've never gotten around to doing the cable.. so it's 100% open all the time! When I manually close it up (to about 90%... don't want it 100% blocked!) it's not too much different at idle/low revs but really noticeable at higher revs. I must note that i have a VERY LOUD exhaust on mine... only intensified by the fact that it's NA :D

haha nice my mate i used to work with hooked up a throttle body to his exhaust that disconected it from the muffler was loud as f**k but i bet it lost a shit load of power any way it ended up melting it XD stupid fool

haha nice my mate i used to work with hooked up a throttle body to his exhaust that disconected it from the muffler was loud as f**k but i bet it lost a shit load of power any way it ended up melting it XD stupid fool

Power loss was half the reason i put the butterfly in... see it's a 3" system off a turbo (JASMA) but because mine is NA the power is too far up the rev range... i.e. I've got NOTHING until about 5K... then it pulls pretty hard up to 7.5K (limiter :D)

The way I understand it, for a turbo you gain backpressure between the exhaust valves and the turbo impella... whereas on NA, the exhaust needs to provide the backpressure. So for turbo, you want the most free-flowing exhaust possible, but for NA you need to make sure it's not too free flowing. My logic was that at idle, the valve would be almost shut, creating enough backpressure to bring my power down to a nice, usable rev range. as I reach 5K RPM, the valve would open, my power range would be shifted up a bit, and I would continue to have power to redline/limiter.

Because I've never gotten around to hooking it all up, I can't really test this theory though! Like so many other things on my to-do list... one day... one day...

If you're using this system with its valve closed off for street, day to day driving it should be fine. It's only when you're trying to push your engine is where I see problems occurring. The system is designed to make the car/engine quiet. If you want performance out of it as well, you're not gonna get any.

lol no one has awnserd if it could cause problems!~

With it's bypass system when closed, I can't see any problems occurring. Obviously you will loose some power as there is extra restriction in the line (I'm assuming you've got a turbo), but it's not gonna be that bad that it doesn't flow at all (which can cook a catallytic converter pretty quickly!). Just think of it like having a 1.5" exhaust instead! When you want power, you open it up and you've got power along with noise.

I was looking at these, but I wasn't sure how good they would be. I want one cos my car is very loud, and my neighbours r cops, and i want to be able 2 come home at early hours of the morning without waking my parents. Does anyone know anywhere in WA who sells them? Or will I have to get it sent over from Sydney?

From what I can see from other videos, you can control how much of the valve you want opened/closed.

I haven't got this installed myself, but having the valve closed fully shouldn't do any harm if you're just doing street driving. You shouldn't be trying to push the car with the valve closed anyway.

  • 1 year later...

Got one of these Varex's on my car saved me so many times from cops, even this morning pulled up next to a copper and he waited for me to take off and make noise but had it closed...

It does restrict your car on take-off if its closed if you are trying to drag off the line, obviously cause of restrictions but doesnt damage it at all driving with it closed have had mine for over a year now

You can set it at full open or full closed...but can have it set half way as well if you only want a bit of noise, sounds mad going through tunnels and turns heads all over the place

Any other questions PM me for details, I got mine done in Melb so I dont know dealers in other states, but I know there are a few in Sydney while I was up there was checking it out

these things are an awesome product. Mate of mine has one on his evo coupe and its perfect for the quiet times and the obnoxious ones. Its tuned for open as i understand it and when closed makes very little difference to the cars running other than sound. Its a mild increase in back pressure so it's most likely that only effect is a slightly lower response on boost cut in (Ie a poofteenth of a second of lag)

But dont be fooled the mufflers are very quickly going to become illegal if they arent already. Anything that enables you to change exhaust note is bound to be illegal as you can go from adr compliant to not in the push of a button.

  • 2 weeks later...

they shudnt make these illegal, cause some ppl do use their cars on both track and roads so its fair enuf, obviously proper track cars cant b registered for road use so i mean the ones ppl use for both

personally during the day on hwys and fwys u shud b able to use them and it shud b illegal to hav it loud at night in suburban sts...at least we are high compliant compared to sum ppl who just chop their exhausts... :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey guys! Y'all are the masters so figured I'd check in on a few items here. - My engine sounds ever-so-slightly more raspy than the other NA RB25s I've listened to. It's barely noticeable but definitely a slightly different sound. - When I back off the throttle at high RPM, I will sometimes get a pop out of the exhaust, assuming this can be diagnosed as misfire. Some history on the car: - Had an exhaust leak in auction sheet but was claimed to be fixed by seller (bought from USA importer).  - Car's coil packs and sparks were replaced when it was sold to me, but unsure on what the gap is and whether the coil packs are correct.  - A prior mechanic had misdiagnosed a pilot or throwout bearing sound as LSPI/detonation. Had played with timing a bit, pops/raspy sound of engine just got worse. Got timing reset. - Had failed emissions a few times. First time went in as is, failed. Second time, replaced cat, still failed, running rich as hell. Third time replaced o2 sensor, passed. Car still smells gassy though. - Timing belt and valve cover gasket also replaced.  - Gas mileage is... low. about 350-400K per tank.  Any idea if I'm having any serious issues here or does this all sound like normal old NA RB stuff and I'm fine to drive it with the pops/slightly raspy engine? If it'll help, I can get drop a video of the sound of the engine.
    • So....to find any R chassis part number, get your VIN (will be something like ER33-xxxxxx for you) and go to: https://www.amayama.com/en/genuine-catalogs/nissan and enter it. From there you have access to a web version of Nissan's part system, FAST. It is a bit tricky to get used to, so maybe have a shot and post up what you think.  You can also search by general model but note in some cases your car might have different options so VIN is safest.  On diagram 211 I got 14075-75T16 for Connector, Water Hose If I search for part 14053‑21U10 that you posted, that is also a water hose but not the one bolted to the plenum and 14075‑04U00 is the fitting where the water hose goes into the block.
    • Yeah now we are talking I much prefer coolers in the front middle because it lessens the chance of a small bump to a corner stopping the whole event. I was thinking the AT cooler can move out of the radiator, delete the AT/engine coolant interwarmer and mount a separate cooler with a thermoswitch somewhere further back as is common in racing, that would be one thing. Beyond that, the engine oil cooler is an obvious one to move to the wheel arch, potentially one on each side, but unused space is an issue. I did have a earlier pic with the bumper off but it doesn't show how busy the corners are: DS is full of the auto driving sensors and PS is totally fully of windscreen washer fluid reservoir But ultimately I was hoping to keep the AC, and the water/air heat exchanger is fundamental so it is not just the radiator that needs to be in front BTW here's airflow to the rad as it ran at the track (one horn is gone now and I'll remove the lights next time):
    • your right the maps for Australia came out in 2017 but are 2010 maps. i got the updated maps SD card put it in and it was the same. Same maps in my Brothers Nissan Patrol. 2020 i think his car is
×
×
  • Create New...