Jump to content
SAU Community

Recommended Posts

The car landed in April 2005 and was complianced by Carizma. I am the first owner in Australia. I Imported the car through imports101. This car has always been very reliable, and the only problem I ever had was with the original RB20DET engine, which dropped a cylinder. At the time I was quite annoyed, but it gave me a reason to put in an RB25DET!

All the necessary engine conversion work was done by Roshan at Driftline Racing. No corners were cut, and i ensured everything was done as well as it could have been.

I have done a few track days in this car, and has never really given me any problems, besides overheating when i first got the new engine. So I put a dual core radiator in, and it solved the problem.

The Rear seats, Carpet and sound deadening have been removed and the entire floor has been painted matt black. This was done in May 2007 this year. At the same time, I had the majority of the car Re Sprayed to freshen it up when i put the Type-m kit on.

The Engine and gearbox came out of a R33 Series 2 GTS-t front cut.

The car has had a brand new Exedy heavy duty clutch fitted. I have a new Nismo 2 Way which is getting installed within the week.

I do have all the original interior, carpet, etc which will go with the car :P

These days I don’t drive the car much so its time for it to be sold and put to better use by someone else.

Kilometres: 65,000 (Engine swap was done at 49,000)

Complianced: Yes

Registered: Yes, Until April 28th 2008

Transmission: 5 speed Manual

Engine: 6 cylinder RB25DET Turbo 2.5L

Modifications:

***ENGINE***

RB25DET Engine

Greddy Intercooler and Piping

Dual core Radiator

Twin Davis Craig Thermo Fans

Greddy Oil Catch Can

Custom 3 Inch Exhaust w/High Flow Cat

Z32 AFM

Dr Drift Boost Controller

GTR Fuel Pump

Pod Filter

***ECU***

Power FC with Hand Controller

Tuned by Dr Drift

***DRIVE TRAIN***

RB25DET Gear Box

Custom R32/R33 Tailshaft

NEW Nismo 2 way

New Exedy Heavy Duty Clutch

Tomei Electronic Hicas Lock System

***SUSPENSION + BRAKES***

HKS Hypermax Suspension

Cusco Adjustable Castor Rods

Cusco Front and Rear Sway Bars

Cusco Front and Rear Strut Braces

***EXTERIOR***

R32 GTR Wheels

Vertex Front Bar

Type-m Side skirts and rear bar

Flared rear guards (wider than usual)

ReSpray in Custom Gold

R32 GTR Black Bonnet

***INTERIOR + ENTERTAINMENT***

MOMO “RACE” Steering Wheel

Bride Brix II Seat

2 HKS Water Temp Gauge

HKS Eng Temp Gauge

Pivot Full Auto Turbo timer

Immobiliser (Playing up, may as well throw it out the window!)

Producing a SAFE 210RWKW @ Dr Drift

$16,000

Oppen to offers

Contact Troy...

[email protected] (Also for MSN)

0409875864

Car is Currently located 1hr from CBD

Will take some more pics tomorrow and put them up 

sky8.jpg

picture 1

picture 2

picture 3

picture 4

picture 5

picture 6

picture 7

****************************UPDATE**********************************

Sorry these pics arent so great.. only got camera phone atm!

pic2.jpg

pic3.jpg

pic6.jpg

pic8.jpg

MORE pics

click here

click here

click here

click here

Edited by Prospector
Link to comment
https://www.sau.com.au/forums/topic/201357-r32-gts-t-rb25det-pics-updated/
Share on other sites

  • 2 weeks later...

unfortunately i have had a delay on the diff...

If anyone wants to buy the car without the new diff, (still has a kinda working 2 way nismo)

Then i can work out a price, contact me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...