Jump to content
SAU Community

Recommended Posts

Unbolt the s/wheel off the boss/hub, check to see if the HICAS sensor shaft is poking through a plastic locater, thus when the s/wheel turns the shaft turns the sensor.

If not go to your local commercial rice supplier (in Vic it's Autobarn) and buy a HKB boss kit to suit a R33 with HICAS, about $80.

For my car R33 GTST (with hicas) part number: ON-177

Here is a Just Jap link, scroll half way down the page: http://www.justjap.com/parts_ninterior.htm

i have also heard that hicas sensors can just be dodgey after the years, so it may be something you cant fix unless you wanna get another sensor. We have just given up with flicks 32 as it randomly comes on and off.

hicas light is connected to a number of things. Power steering, speed sensors, steering wheel sensor and hicas.

Power steering - known issues like low fluid, or even leaking fluid from the cap which runs down the wires off of it and soaks the connections can set the light off...

Speed sensors - is the speedo working? Back of the dash sensor working? If your car as a faulty sensor it will drive 400m up the road and trip the steering into saftey "hicas mode" and the steering would go heavy with the light come on (had this one myself)

Steering wheel sensor - mentioned above

Hicas - Is it still working? Have u actually checked it is? I recommend a Tomei Hicas lock kit for a street driven car if u dont want Hicas anymore. It contains 2 brass small shims fitted to the power steering rack which go under the steering boots (hidden), and then the best part - a small black box that is wired into the hicas computer to keep it thinking everything is working with the hicas - basically keeps the hicas light off on the dash.

If u have thoroughly checked all 4 then your hicas light wont be on :banana:

Edited by Bl4cK32

For those that are not aware: ArenaGTR has an R33 GTR, thus oil levels and any oil related issues do not apply to an electronically controlled HICAS system.

Have you checked under the car, at the HICAS control unit? it could have been removed or it could be unplugged.

I would still check the s/wheel hub.

Have you ran a diagnostic on the ecu for error codes (never done one myself so you'll need to use the "search" button)

I would personally remove the HICAS unit, fit a HICAS lock bar, get a 4 wheel alignment and remove the bulb from the dash cluster. Problem solved :glare:

Nah, didn't have time to do any checks, cuz when I picked up the car from the docks I had to drive it straight to the compliance workshop, luckily when I was driving down there, cops spotted my car without number plates, but didn't pull me over, pheww....

but yeah, will definately do diagnostic check once I get my car back from the workshop ^^

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...