Jump to content
SAU Community

Recommended Posts

hi guys

I have a 1998 R34 and i have a problem there is an A/T light located just below the check engine light i dont have a clue wat it is but when its on i lose all my power also the car is shuttering and the engine light is on does anyone have any ideas on wat the problem could be. hope someone can help me . thanks

Link to comment
https://www.sau.com.au/forums/topic/205708-i-need-help/
Share on other sites

  raps86 said:
wat sort of mods do u have is it an auto/manual. is it an intermitent problem or all the time. mite help sum guys on here help u with the prob

no mods yet its auto and it only comes on sometimes

Link to comment
https://www.sau.com.au/forums/topic/205708-i-need-help/#findComment-3640828
Share on other sites

A/T light located under the check engine light

The A/T light comes on and the car loser power has anyone had this problem before

check engine light

And the car shutters wen the engine light comes on i was told it was a crank angle sensor and they replace it im thinking its the coils.

Link to comment
https://www.sau.com.au/forums/topic/205708-i-need-help/#findComment-3640981
Share on other sites

  raps86 said:
the onlything i can think of at the moment is the fluid in the auto beign low. Check the levels and c if they r on the mark. otherwise ring round a few places and c wat they reckon

i have checked the fluid and thet seems fine maybe i mght change the gearbox oil and see wat happens.

Link to comment
https://www.sau.com.au/forums/topic/205708-i-need-help/#findComment-3643649
Share on other sites

  r34 gt25 said:
i have checked the fluid and thet seems fine maybe i mght change the gearbox oil and see wat happens.

i have disconnected the battery and now the A/T light hasnt stayed on hopefully it wont havent driven it yet,

fingers crossed

Link to comment
https://www.sau.com.au/forums/topic/205708-i-need-help/#findComment-3649220
Share on other sites

have had it happen to me once or twice just driving along and noticed that it won't change to 4th even if you put it in tiptronic so i just pulled over turned the car off and on again and it was fine a/t light went away and changed gears fine. So i thought the computer just had a hiccup. i thought that was a gearbox warning light. it has the same letter on the traction control button says A/T snow on mine might have something to do with that?

Link to comment
https://www.sau.com.au/forums/topic/205708-i-need-help/#findComment-3649413
Share on other sites

  r34 gt25 said:
i have disconnected the battery and now the A/T light hasnt stayed on hopefully it wont havent driven it yet,

fingers crossed

yeah maybe cos it feels like its taking off in second maybe very sluggish

Link to comment
https://www.sau.com.au/forums/topic/205708-i-need-help/#findComment-3649516
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...