Jump to content
SAU Community

Recommended Posts

(i have added the same post under 'general maintenance')

i am looking for replacement boots for my handbrake & gear shifter - preferable leather OR if not leather then i'd be happy to change just the handbrake boot in the factory vinyl so it matches the gear shifter.

where can i source this? i have searched all over the forum

regards,

I got a pair from a seller on eBay in England. Real leather and your choice or colour scheme (i chose white and black). Name was Mr Gaiter but no longer registered user, pretty sure he is on there with a different name, foudebuzi or something

I got a pair from a seller on eBay in England. Real leather and your choice or colour scheme (i chose white and black). Name was Mr Gaiter but no longer registered user, pretty sure he is on there with a different name, foudebuzi or something

i think i found gaiters - is this it?

http://cgi.ebay.com.au/NISSAN-SKYLINE-GTS-...bayphotohosting

buddy your link doesnt work...

i brought a set of handbrake and gear shifter boot of ebay from gaiter for my r32 gtst..

fits perfect with some minor adjustment. has the wiring at the bottom of the base as well. saves u time from taking it out of your old one...

its leather and makes the car look like new...

here it is as per image!

not sure if i should go with the GTR emblem or plain black leather...also comtemplating on black stitching or red stitching, thoughts?

post-8728-1203492891_thumb.jpg

Edited by Marko R1

Here you go, this is the one you want.

Gaiter boots

I got these and they are very good quality.

Just make sure you specify exactly what car it's for and what colour leather and if you want the logos or not.

EDIT: Damn, just beat me :rofl:

GT-R logos are ok, if I got them again I'd just get the logo on the handbrake.

Edited by bigslick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...