Jump to content
SAU Community

Recommended Posts

hey!

I have a bit of a hypothetical question for a few cluey engine gurus

i am planning a trip to look at a a car (r32gtr) over 3000 kms away.

Now after pumping this guy for as much info on the phone as i can this is what i have managed to get out of the convo

the car has some sought of vapor coming out of it on down changes which the owner says he has been told the cat is buggered after he took it into get a new cannon put on it and that its whats causing it to blow smoke etc on a down change

he tells me that he reset the PFC back to base map because the engine was detonating after the exhaust mod which i would assume the car is running rough/Rich...

does a worn out cat (original or 14 year old Approx) make exhaust vapor/Dust on a down change or is there something maybe wrong elsewhere in the engine ?

the strange thing is that he only reset the pfc after the exhaust change so i am thinking its not fuel coming out of the exhaust as the exhaust place was the one that told him his cat was buggered and this maybe the cause of the mysterious gas/dust/fuel/oil comong from the exhaust pipe...

Could someone help me out on what maybe going on with this...

he is fairly sure its not blue smoke but in saying that he dosent understand engines to well either

thanks Dj

Edited by ish

Those vapours could be from an ATMO or hybrid BOV on a down change. At high rpm a blocked cat can cause a leak b/n flanges

Sounds ok, increase in breathing hence running richer thus noticably more smoke. Without a tune it would run rough, if not stall with the ATMO unless compensated for with the PFC. Not sure about the detonation, maybe it has something to do with the missing air that the atmo releases and the sys. cant meter

LOTS AND LOTS OF SMOKE. FILLS UP THE CABIN, CANT BREATH, PINK SMOKE BLUE SMOKE YELLO SMOKE AND SMOKE SMOKE.. :-P

Pretty sure All skylines pump a bit of smoke out if they have not been drivin in a long period of time.. gotta remember its a 18 year old car..

CHEEEEEEEEEEEEEEEEEEEEERS

could be the pcv valve sucking excessive blowby in when the car decelerates and engine inlet manifold vacuum is high. pcv valve is closed under boost.

otherwise if the car is cold and has atmo bov, could be dumping fuel in on decel because of the unmetered air exiting the bov, when its hot it should fuel cut altogether (turn off injectors) on decel so you shouldn't get fuel smoke from atmo bov.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...