Jump to content
SAU Community

R33 Whiteline Adjustable Rear Sway Bar

SevenAngryPenguins

By SevenAngryPenguins,
in Classifieds

 Share

Recommended Posts

SevenAngryPenguins Proficient

SevenAngryPenguins

Posted
Posted (edited)

Near new whiteline adjustable 20mm rear sway bar (BNR11Z) This bar is something like twice as stiff as the stock bar on the softest setting, but don't quote me on that.

Only been used on the car for a few weeks. Comes with new/unused links and link bushes. D bushes have been used but are in new condition. Also comes with 3/4 of a bag of grease, should be plenty only used a bit to grease my new D's.

Location - Brisbane

Price - $180 ONO

post-36364-1206657853_thumb.jpg

post-36364-1206657869_thumb.jpg

Edited by SevenAngryPenguins
SevenAngryPenguins Proficient

SevenAngryPenguins

Posted
  • Author
Posted (edited)

very easy takes about 45mins or so, just need some car ramps to make life easy

have the new bar now so old one will be off by the weekend

Edited by SevenAngryPenguins
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...