Jump to content
SAU Community

Recommended Posts

Make:Nissan

Model: 1996 Series 2 S14

Milage: less thant 5000km

Transmission: R33 GTS 5sp Manual

Colour:Red

Location: Brisbane

Complied? No

Currently registered? Yes

Price:$35000

Contact: Matt 0402 072 226

Comments / Modifications:im selling this car due to the fact i lost my licence before it was finished being built and i will have a company car when i get it back.

it is powered by a 450hp built rb26 det.

ENGINE INTERNALS

40 thou oversized cp pistons

Spool rods

brand new genuine r33 gtr crank

N1 oil pump

acl race bearings

enlarged 7.5L sump

Tomei head gasket

tomei oil restrictor

tomei type b poncams

aftermarket valve springs

800cc Seimens injectors on an anodised red aftermarket fuel rail

Sard fuel pressure reg.

6 BOOST merge collector exhaust manifold

Garret GT35/40r Turbo

Tial 44mm Waste gate

EBOOST 2 boost controller

KLS 300x600x105mm intercooler with custom 316 stainless 3" piping

Turbo Smart Blow off valve

3.5" TPS stainless exhaust

RB25 gearbox

NPC 5puck brassbutton clutch for a patrol

Autronic SM4 ecu

FUEL PUMP

Lift pump

Bosh 044 External fuelpump

Alloy Surge tank

INTERIOR AND STEREO

eBOOST 2 boost controller on pillar

Saber oil temp, oil pressure, water temp gauges

Alpine head deck

Type R splits in rear

Some wicked Splits in front (cost me $900, but cant remember the brand)

Type S 300WRMS Sub

Alpine Mono Block Amp for sub

Alpine 4 channel amp for speakers

Stereo sounds great come hear it for yourself.

UNDERBODY MODS

Petron Automotive 800HP one peice tailshaft

R33 gts rear cradle (includes diff, cv's, hubs, shocks, brakes, control arms)

18 inch 3 peice rims

Images: will get some more up asap

post-33311-1207554058_thumb.jpg

im 100% sure it would make well over 450 hp but after spending over $60k on a car im a bit strapped for cash to spend on a tuner considering i have already paid for a tune that i never recieved.

(workshop dicked me around)

anyone know what it might do down the quater???

well im making 405hp in a vl sohc head but with a auto and am told it would run 10.5 and as manual is a bit harder to shift but you will surely have more power i'd say somewhere around 10 sec

check it out

my vl 4 sale

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...