Jump to content
SAU Community

Elitemotorsports

poyz

By poyz,
in Australian Capital Territory

 Share

Recommended Posts

Kdawgboostin33 Collaborator

Kdawgboostin33

Posted
Posted

Dude if It did not do it b4 the BOV check the plumbing is not leaking for this. John W had a similar problem, was firing the spark, down the sides of the plug, not directly at the plug, either way get it checked out could not recommend Dave at Gastune highly enough!

Zheng Ye Contributor

Zheng Ye

Posted
Posted

well I did take it there.....they said they could not find anything.

then I found out (on another forum) that there was a little solinoid that adjusts boost. 1 to 5 RPM- 5PSI then 5 to 7RPM- 7PSI. I bypassed it and found it stutters whenever it gets passed 5PSI see if I dont floor it, it wont stutter (from idle all the way to red line). as soon as it gets past 5 PSI does not matter at what revs (3 to 7RPM) it will stutter like hell. by the way the solinoid is near the wastegate (connected with pipe). anyone help?

Zheng Ye Contributor

Zheng Ye

Posted
Posted

it's so bad that in a drag I just beat a standed ford falcon.

does this suck or what. I even had all the plugs and timming belt changed ($600) but still nothing. I really think it's my air flow sensor....see when me and my friend left the AFS unpluged it did the same thing....though it done it as soon as it hit boost.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • GTSBoy
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By GTSBoy · Posted

      I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...