Jump to content
SAU Community

Recommended Posts

Hello

I put my RB25 turbo onto my R32 GTS-T RB20 and I notice a improvement. The car seems to take off better and seems to go abit faster and less lag.

I still have the original intercooler on there.

How much is the stock intercooler restricting any new gains I will get from the turbo change?

I have a R34 intercooler I am going to put in as soon as I can get it modded to fit.

With a catback exhaust, intake, and the RB25 turbo, how much hp over the original hp will I probably be getting?

Also is there anything else I need to do to make this mod better? Will upgrading to a 555cc fuel pump help at all?

Help

hey mate once you have the intercooler sorted, i would say your next step should be finishing off the exaust.

fit any 3" front/dump pipe and a high flow cat, as the stock ones are very restrictive.. you should feel the difference right away

agreed.

once that is done, get your self a $30 turbo tech boost controller, a walbro fuel pump, then talk to "TOSHI" or "CEF11E" from these forums regarding remaps

will cost you from about $100 - $200 for the remap.

12-14 psi (depends on what you want to run and what you feel is safe) should net you somewhere between 170-190rwkw depending on Dyno.

agreed.

once that is done, get your self a $30 turbo tech boost controller, a walbro fuel pump, then talk to "TOSHI" or "CEF11E" from these forums regarding remaps

will cost you from about $100 - $200 for the remap.

12-14 psi (depends on what you want to run and what you feel is safe) should net you somewhere between 170-190rwkw depending on Dyno.

So in order to see any gains, I have to get a remap or tune? I have a HKS adjustable acuator on the turbo(came with it) I don't know what its set at. Does anyone know how to adjust these?

It should have more lag now. I've had first hand experience with this. It's likely you feeling the difference because you want too feel it.

The amount of extra lag depends on the type of RB25 turbo you use.

The R34 ones should have a nylon compressor wheel so they have less lag then the steel S1 R33 turbos.

The amount of extra lag depends on the type of RB25 turbo you use.

The R34 ones should have a nylon compressor wheel so they have less lag then the steel S1 R33 turbos.

not true. R33 series 2 turbos have the nylon compressor wheel also. the R34 turbos actually have more lag due to a slightly bigger exhaust wheel and housing than the R33 one. i've run a series 1 (steel comp wheel) and a series 2(nylon comp wheel) on my 32 when i had it and didn't notice any difference between the two.

Yeap Josh above me got it right .. r34 has a bigger exhaust housing vq30? will go like crap on a rb20

R33 turbos will bring boost on latter to as you have less exhaust gas in a 2L

a tune will be needed to bring more power...

i was actually still hitting full boost (13psi) around 3000 - 3500rpm. so not that laggy, very drive able. i found that it still came on boost around the same time but just kept pulling through the rev range instead of flattening out like the stock 32 turbo does.

and Mike, like everyone has said. get a full exhuast setup, put the R34 SMIC on or just get a FMIC kit and put the on, get the ecu chipped or even just a fuel computer like the SAFC in and tuned. set the boost to 12-13psi. definately get a new fuel pump, as yours is 15 years old or older and will probably be on its way out soon (p.s. do the pump before the tune :thumbsup: ) stock injectors will be ok on this setup. and as GTST hs said, it should see you around the 180rwkw mark.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Spotted in Adelaide last week.... mine! New to me two weeks ago.. love it!
    • Congrats on the career change!  I did something similar at the start of the year too, left IT / corporate after nearly 2 decades. Soooo when's the motor coming out for the spark plug change?
    • Hi guys, long time no post as per usual! It's been a busy year so far, the biggest thing being a new job.  After 28 years in the automotive industry I decided it was time for a change.  I was losing faith in the industry and where it's heading.  Now in a completely different industry (electrical) working for a company that manufacture water pump contollers.  Not as sexy as cars but it's an interesting,  challenging industry. I now don't work Saturdays which is a bonus!  It's still 50-55 hours a week but having Saturdays ack after 28 years of working them is awesome!   No news on the GT-R but i did decide to add some more JDM goodness into my life....           1990 300 ZX.  She's not perfect but for a 35 year old car she ain't bad!  Just going to tidy it up a bit and enjoy it.  It's currently auto but will start stockpiling everything for a manual swap. It WILL distract me even further from the GT-R but im hoping not for too long! It somewhat proves a 6'8" freak can fit in a 300 ZX.  Sort of...  I drove it home from the previous owners house in Melbourne via Black Spur and Merton Gap (2 awesome bits of Victorian twisty road) and it was amazing!  Handles so well!!!   I don't think it would be worthy of a full build page but I'll post up some of the upgrades here if anyone is interested?  Cheers guys!
    • End game is to: - Remove all the slop from old worn parts - Adjust setup so that the wheels actually fit and the car is drivable (currently it is not because of the extreme rubbing on the guards).   Progress over the last couple of days, removed the rear hubs! Next steps: - Buy bushings - Replace bushings/bearings on hub - Reinstall
×
×
  • Create New...