Jump to content
SAU Community

Recommended Posts

Item: Bride Low Max Gias Carbon Kevlar Seats, Blue in colour with super low bride rails

Age: 3 months

Condition: Like new

Price: Trade Standard R34 GTR Grey with red stitching seats plus $3200.

To Fit: (What car) R32 R33 R34 GTR

Location: Perth

Contact: [email protected]

Comments: Great seats, i am getting sore legs as i am not tiny therefor suits someone else. Awesome seats, very comfortable in the lower back and minimal movement when turning. Carbon Kevlar looks great too.

  • 2 months later...
  • 1 month later...
  • 4 months later...
  • 3 weeks later...

I havent had time for pics lately.

Will get some this week.

barely used, barely ever have a passenger in the car either.

Have been sitting in the car on the hoist for months. Very good condition.

$2900 is cheap these are like new sitting in the car not being used. Wouldnt want to know the price for these from Japan at the moment...

these brand new are $2000 each, and the rails are about $220 each... not a bad price mate, put some pics up mate, they should sell quicker then.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...