Jump to content
SAU Community

Recommended Posts

Hey guys,

Just got done for speeding, $700 and 5 demerit points. Won't go into details, but it is my fault and I deserve it.

However, my mate says that if you were to lose 4 demerit points or more at one time while on your Ps, you lose your license for so long. Does anyone know if this is correct? I couldnt find any details on the DPI website. Sounds like something the government would do, another stupid law.

Lets hope he's wrong!

Cheers

Rhys

Silly silly boy Rhys....

did the fines change in price?

i think 2 years ago i did 123km/h on karrinyup road which is a 70km/h zone and all i got was 350$ fine and 6 demerits. Took them 6 months to call me and give me the fine.

did the fines change in price?

i think 2 years ago i did 123km/h on karrinyup road which is a 70km/h zone and all i got was 350$ fine and 6 demerits. Took them 6 months to call me and give me the fine.

Yeah, anything over 20kph over the fines have risen, cause of the hoon law

Yeah, anything over 20kph over the fines have risen, cause of the hoon law

Fines rose the whole way, not just 20 over, and it's not cause of the hoon law...

0-9 $75 instead of 50, still no points.

10-19 $150 2 points instead of $100 and 1

etc etc

45+ hoonlaw.

Nah, I meant recently it went up again, but you were right it wasn't cause of the hoon law,

"Penalties for speeding have increased in line with the known risk of crashing from this type of behaviour. Penalties have increased for drivers who continue to speed on the State’s roads by more than 20 km/h. Other speeding penalties remain unchanged."

http://www.officeofroadsafety.wa.gov.au/in...topicsPenalties

I thought it was because the.price of donuts and strippers had risen??

And Marko, that wasn't actually a joke. I was honestly waiting for you to do the whole father lecture thing because I didn't listen to your warnings. Still, it's been done and I hope I learn from it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...