Jump to content
SAU Community

Comprehensive 4 Point Bolt-in Cage With Side Intrusions And Harness Bar

Snowman
 Share

Recommended Posts

Snowman Grand Master

Snowman

Posted
Posted

Item:Comprehensive 4 Point Bolt-in Cage with Side Intrusions and harness bar

Age: 18 months

Condition: Excelent

Price: $1100

To Fit: (What car) R34 GT-R but can fit other GT-R's

Location: Merridian Motorsports - Melboune

Contact: Andrew - 0419 375 140

Comments: Protect your ass without wrecking your car!!

I have a comprehensive custom made 4 point Bolt-in cage with side intrusion and harness bar that meets CAMS regulations and is fully street legal. No need to remove rear seats (although you won't be able to use them obviously) or damage any major part of your car.

It was designed and fitted by Merridian Motorsports (cage is there now) and was done for my R34 GT-R although they currently have another exact cage that has gone into an R33 GT-R and they are exactly the same size in length but this cage is 50mm narrower than an R33 cage which just means it will still fit but there will be a small 2cm gap at the B pillars on each side if fitted to an R33. Not sure about an R32 however - it would be best to contact them.

If anyone in Melbourne wants this cage Merridian will also happily assit you in fitting it. http://www.mmsport.com.au/

This cage has been fantastic and was used in my car when I won the Dutton Rally in 2007. It's only being sold as I am upgrading to a full weld in through the dash jobby 6 point cage so I can do Targa next year. I have a couple of basic pics now (not easy to take pics of in the car!) but will try and get some more pics from when the install was done in 07.

post-5136-1222131532_thumb.jpg

post-5136-1222131819_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...