Jump to content
SAU Community

Recommended Posts

These rims i brought on the weekend as skid rims. THey are 16 inch by 8 inch two peice i think. They have Tommy Kaira stamped on the inside along with the word japan. Would like to know what they are meant to be off. PCD is 5/114.3 cheers.

dsc01184zw6.jpg

dsc01179yw4.jpg

dsc01181tk7.jpg

dsc01182pe7.jpg

dsc01183en2.jpg

Edited by super_s13
Link to comment
https://www.sau.com.au/forums/topic/238997-anyone-know-what-these-are-off/
Share on other sites

I think I have seen them on a Tommi Kaira R32 GTST

Actually im positive this is the model they came on.

I am trying to find the pics, but if you are looking to market them... then thats what they are off :)

Thanks. WOuld be great to get some pics of them on a car. I googled the shit out of Tommy Kaira r32 but cant seem to find anyhting. Not looking at marketing them as i paid to much for them as it is. $400 with tires but i neeed skid rims so i am going to clean them up and paint the inside and polish the lip. If you find some pics can you post them up

Thanks heaps mate.

Only to happy to help out mate.

Here is your rims, on the Tommy Kaira M20. Its an R32 GTST model that tommy Kaira modified. And there is your mags :) Centre caps attached in these photos though.

post-41581-1223297370_thumb.jpg

post-41581-1223297548_thumb.jpg

And once again here are your wheels on the Tommy Kaira M30. This was a NA 3 litre version they did pushing 280hp. :rofl: pretty extreme!

post-41581-1223297885_thumb.jpg

post-41581-1223298041_thumb.jpg

post-41581-1223298101_thumb.jpg

Hope these pics help you out :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...