Jump to content
SAU Community

Fs: Ssr Professer S1

nerm
 Share

Recommended Posts

nerm Mentor

nerm

Posted
Posted (edited)

Item: Chrome SSR Professers S1

Age: ?? came with car

Condition: used, some gutter rash and dents

Price: $800.00 (tyres alone were $640)

To Fit: (What car) 5x114.3

Location: Canberra

Contact: Nirmal. PM me or 0410 149 684. email address in [email protected]

Comments:

2x Chrome SSR Professer S1 17x8 +38 (unsure for offset and will confirm tonight) with brand new tyres.. 235/40 (or 45?)

2x Chrome SSR Professer S1 17x8.5 +28 (unsure for offset and will confirm tonight) also with brand new tyres.. 235/40 (or45? will confirm tonight)

I also have two 4mm spacers that were on the front of my car when it was purchased which the buyer can have

I'm pretty sure that the fronts (17x8) will not fit on a R32 gts-t m-spec (4pot front calipers) without a spacer (unless you grind down the caliper cover). ZCR test fitted the rears and it looked... awesome!! fills the guards nicely. for pics of his 32 with these wheels on the rear check my forsale tread in the ACT section

I will ship interstate at buyers expense

the picture below is the wheels on my car with the old tyres still on them. i will take some closer pics showing the gutter rash etc tonight

Nerm

Edited by Ex!$t3nZ
Link to comment
https://www.sau.com.au/forums/topic/240423-fs-ssr-professer-s1/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...