Jump to content
SAU Community

Recommended Posts

R32 GTR

165000km

gunmetal grey

Brisbane

registed till may

$19000

leather momo steering wheel,

personalised number plates,

sony dvd/mp3 player,

alpine and pioneer 6x9 front and rear apline tweeters,

alarm and engine immobilizer,

central locking,

ultra turbo timer,

17" rims, 2 brand new toyo t1Rs 235s,

4000 series dba discs,

ferodo DS2500 brake pads,

nismo stainless steel brake lines,

cusco brake cylinder stopper,

cusco adjustable pillow tension rods,

jic strut brace,

whiteline front and rear sway bars,

bilstein shocks all round,

nismo twin plate super coppermix clutch kit,

nismo strong release fork pivot,

nismo big operating slave cylinder,

aftermarket exhaust including mines front pipe,

splitfire coilpacks,

apexi power fc,

apexi avcr,

nismo 600cc injectors,

apexi pod filters,

arc intercooler,

hks intercooler pipping kit,

been looked after extremely well ive never had it on the drag strip or race circuit.

This is great car to drive, extremely clean.

post-a173931-DSC03154.JPG

post-a173932-DSC03156.JPG

post-a173933-DSC03170.JPG

post-a173934-DSC03161.JPG

post-a173935-DSC03169.JPG

post-a173936-DSC03132.JPG

post-a173937-DSC03166.JPG

post-1453-1225433623_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/242684-r32-gtr/
Share on other sites

  • 3 weeks later...
  • 3 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...