Jump to content
SAU Community

Recommended Posts

Hey mate,

If your after a serious motor.. Im toying with the idea of selling mine, All parts are brand new.. Pm me for a price. (I havent done the numbers yet)

Motor was built by Paul at Red R Racing,

Standard Block 05U (one hell of a port Job!- check out my build thread for pics.)

Custom RIPZ NZ sump with baffles and modified pick up, #10 breather and oil return lines. (on its way from NZ as we speak)

Fully balanced bottom end (std crank)

Greddy Oil pump

N1 Water pump

86.5mm CP pistons and rings

Eagle ESP H beam rods with ARP rod bolts

Greddy cams 256 duration inlet 9.1 lift, 264 duration exhaust 9.1 lift

Greddy adjustable cam gears

Tomei timing belt

Tomei Bronze Valve guides RB26DETT In and Ex

Greddy Valve springs

Tomei Solid Valve Lifters RB26DETT Skyline GT-R R32

JUN Titanium Valve Retainers RB26DETT 0 Offset Type I

TRUST Greddy Strengthened Crank Cap Bolt Stud Set RB26

TRUST Greddy Strengthened Cam Cap Bolt Stud Set RB26

Trust Greddy Strengthened Cylinder Head Bolts RB26

HKS Valve Stem Seals RB26DETT Skyline GT-R R32 R33 R34

Tomei Oil Gallery Orifice - oil restrictor

ATI balancer 500HP version

ACL std rod and main bearings calico coated

Mines Cam baffles

NUR spec cam and valley covers

New tensioners

Optionals I have,

6boost low mount manifolds to suit GT25/30's

GT25/30's (used 4,000kms)

Greddy split dump/front pipes

SARD 700cc Fuel Injectors RB26DETT Skyline

SARD Standard Type Adjustable Fuel Regulator #6an

Bosch 044 x 2 external, 040 internal, 1.5 ltr surge tank all braided teflon lines

Greddy 10.5 fuel rail twin entry rail

Custom RIPZ NZ Intake manifold (on its way from NZ as we speak)

http://www.skylinesaustralia.com/forums/Rb...ad-t228029.html

Cheers,

Johno

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...