Jump to content
SAU Community

Recommended Posts

Hey guys. Im looking for some suggestions towards my new car install im doing. I dont have lots of money, so i have to keep it to a form of budget.. but i want good audio still.

What I have is:

Alpine 9881 Headunit

Alpine Type R 6" splits up front

and for rears my friend owed me some money so he gave me some Fusion 6" splits which funnily enough have no crossovers as the split attaches straight to the wire haha... bit dodgy.. But they have pretty good sound quality

I also have a Clarion APX 2180

http://www.clarion.com/us/en/products/2007...5294846853.html

I want to Amp my Speakers

Iv been thinking this Amp

http://www.jaycar.com.au/productView.asp?I...=&SUBCATID=

Im Also keen on a Alpine Type R 12" subwoofer. And to power it im thinking this amp

http://www.jaycar.com.au/productView.asp?I...=&SUBCATID=

Is there any suggestions anyone has for this?? or anything that i should get that would be better value or just better??

By the way i have an R31 Skyline if thats any help

thankss

Link to comment
https://www.sau.com.au/forums/topic/243997-new-car-audio-help/
Share on other sites

sounds good man.. type R subs pound HARD :P

jaycar is meant to be fairly good quality as well, considering the price.

the sub is 500w rms if i remember correctly.. so you might want to get an amp with a bit more juice than that :laugh:

good luck

Ric

sounds good man.. type R subs pound HARD :P

jaycar is meant to be fairly good quality as well, considering the price.

the sub is 500w rms if i remember correctly.. so you might want to get an amp with a bit more juice than that :laugh:

good luck

Ric

Yea from what iv heard from just the speakers im pretty impressed haha. yea the sub is 500rms btu the amp is supposed to put out around 500-450RMS when bridged so hopefully thats enough! haha

thankss

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...