Jump to content
SAU Community

Recommended Posts

Hey people,

'Cleaning the side of my house sale'

all parts are suited for an R32 GTR.

I have:

1 x Passenger side guard in silver $150 (good paint just got a lil bend on the bottom from a rock)

1 x passenger front sideskirt piece $20 or free with the guard (abit ripped)

1 x driver side inner guard $20 (abit cracked here an there but will do the job)

1 x driver side castor rod $30

1 x passenger side castor rod $30 (or both for $50)

1 x broken lip for the front bar. $30 (ezy fix for you plastic welders or fiberglassers betta than payin 400-600

call 0421 835 965 anytime if interested dont pm.

-Steven

post-39597-1228615726_thumb.jpg

Also have some other parts for sale such as:

Nismo water temp sensor $20

Jasma Exhaust Canon the size of the titanic $20 (makes ur car nice and quiet) good for defects!!

Exforce Canon $20

Main Part of GTR catback which

i think is a hks one in mild steel since

my front pipe is a hks one with the same colour and age $50 is 80mm

exhaust parts all have abit of rust on them from sitting around and general age.

again call no pm's

0421 835 965

-Steven

post-39597-1228622779_thumb.jpg

post-39597-1228622799_thumb.jpg

Edited by SideOn

UPDATE

SOLD Passenger side guard in silver $150 (good paint just got a lil bend on the bottom from a rock)

(awaiting pickup) 1 x driver side inner guard $20 (abit cracked here an there but will do the job)

1 x driver side castor rod $30

1 x passenger side castor rod $30 (or both for $50)

SOLD broken lip for the front bar. $30 (ezy fix for you plastic welders or fiberglassers betta than payin 400-600

Nismo water temp sensor $20

Jasma Exhaust Canon the size of the titanic $20 (makes ur car nice and quiet) good for defects!!

Exforce Canon $20

Main Part of GTR catback which

i think is a hks one in mild steel since

my front pipe is a hks one with the same colour and age $50 is 80mm

exhaust parts all have abit of rust on them from sitting around and general age.

again call no pm's

0421 835 965

  • 1 month later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...