Jump to content
SAU Community

Recommended Posts

crap. $30 well spent. although i don't know about the $5 hot dog that was as soggy as a marathon runners undies. yuk!

there were twice as many cars on show compared to last year and some awsome 7 second runs by a few cars, fastest being a mid 7 by an rx7. the drags are still on and the night is getting cooler with a good wind behind them so this time will surely be beaten. there was one skyline but he didn't get a good start.

the burnout comp was great as well including a very skilled driver in a kingswood (i think) that switched to reverse seamlessly three times when he came to the withces hats at the end of the burnout area. i counted over ten sets of tyres blown, five fires and four breakdowns. great show. i missed victor brays burnout but i did hear it all the way at the end of the parking area at the go karts. oh, and i could smell the rubber from there too.

we didn't get the final numbers for attendance but the commentator said there was 25,000 just after lunch time. don't miss it next year guys.

Link to comment
https://www.sau.com.au/forums/topic/24805-supernats-2003/#findComment-528023
Share on other sites

Yeah not a bad day. I arrived at 11am and left at 6:30pm after freezing my nuts off (forgot to take a jumper...)

The Go-To-Whoa was pretty poor. 1/2 the drivers just kept on driving straight past the stopping area without even trying to stop, how pathetic.

The burnout comp I also thought was quite pathetic. Of all the big loud earth shaking v8's sitting over behind the pits we had to put up with 50% of the cars not even able to do a burnout, about 30% able to pull wicked burnouts but died literally 10sec into the session and then the other 20% that could pull monster burnouts but the wind blew awake the smoke before i could even get to smell it (that what burnout comps are for right??).

The show and shine wasn't too bad. Went for abit of a wander over there between the burnout comp and the off-street drags. Noticed 1 skyline (the car from the Burnout comp and off-street drags). He wasn't aware of SAU so I made him aware. Neat car, fmic, pod, 3" exhaust, wheels, abit of paint work on the interior drash trim etc, abit of a sound system, wine red 95 model making 170rwkw.

The Off-street drags look quite promising as they all lined up. None of the crappy parents bombadores or work utes just strong american muscle cars with plenty of grunt. But typical Eastern Creek off-street drags, 5 cars run and then 1 breaks down, 15mins later another 5 cars run and another breaks down 15mins later... and so on. So after 2.5hrs of this and with no jumper and with light drizzle i decided to head home...

So $30 entry, sunburnt face, a life time of goosebumps and 3 dagwood dogs later i guess the day wasn't too bad. Better than watching the footy thats for sure.

I'm not sure what they will do next year coz that drag strip won't exist (but instead across the road at the new venue), so I wonder how that will all go.

Link to comment
https://www.sau.com.au/forums/topic/24805-supernats-2003/#findComment-528479
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...