Jump to content
SAU Community

Recommended Posts

Model: MY06 STI

Registration Number: GIVE WAI

=================================================

Contact: <Wai Yang>

Email: <waiyan at iinet dot net dot au>

Phone: <0402629376>

Location: <WA>

http://www.carsales.com.au/pls/cars...icle_id=6686182

MY06 STi without rear spolier

400HP atw with easy pontential for 700hp without much more work.

Spent close to $120K

Cosworth engine done about 6K (2k were running in w/ no boost)

Chasis has done 29,989km

looking to sell to buy new car.

PM interest. no ridiculous offers.

$80,000

Cosworth Cylinder Heads:

• CNC Ported - New Castings

• Hand blended finish work

• Intake – 21% Increased Flow (average)

• Exhaust – 42% Increased Flow (average)

• 4-angle Inlet Valve job

• 3-angle & radiused Exhaust Valve job

• Valves are lapped

• Back-Cut Inlet Valves

• Heads are Ultra Sonic cleaned prior to assembly

• 1mm Stainless Steel Intake Valves (1800 degrees max.)

• 1mm Inconel Exhaust Valves (2400 degrees max.)

• Performance Valve Springs

• Titanium Retainers

• Hardened Steel Spring Platforms

• Cosworth Billet Camshafts

• Cosworth Head Gaskets

Short Block:

• Custom Machined to a closed deck

• Darton Ductile Iron Flange Sleeved

• Cosworth Forged Pistons

• Cosworth Forged Con-rods

• Cosworth Billet CrankShaft

• Cosworth Bearings

• Cosworth Piston rings

• ARP Head studs

• JUN Oil Pump

• Garrett GT3540r

• Tial 44mm wastegate with screamer

• Greddy Race BOV

• GT spec headers

• Custom Up/Dump pipe

• Catless Exhaust

• K&N POD Filter

• Perrin Front Intercooler

• Cutom Turbo mount/ piping

• Perrin Oil Catch Can

Electronics and Fuel System:

• MOTEC M800 Goldbox, Rotational, Antilag, adv. Functions and Launch Control

• AIM MXL Sports Dash

• Defi Boost, EGT, Oil Pressure

• Apexi Turbo timer

• Alpine 310e DVD player

• 2 x 265l/ph fuel pump

• 800cc Powerenterprise Injectors

• Perrin Fuel Rails

• Aeromotive 1000hp Fuel Pressure Regulator

Driveline Hardware:

• Exedy Twin Carbon Plate Clutch

Rolling Stock, Brakes and Suspension:

• D2 Street Coilovers

• Whiteline front and rear sway bars

• Whiteline front and rear strut brace

• Whiteline Antilift Kit

• Brembo 8 pistons custom mounted

• Slotted disks

Misc.Hardware:

• Perrin Crank pulley

• Perrin Radiator shroud

• Perrin Radiator hoses

• XTR Turbo Bag

• Cobb Short Shifter

• Ignited Engine Start

Exterior:

• Chargespeed side skirts

• Chargespeed Back lip

__________________

Link to comment
https://www.sau.com.au/forums/topic/253292-fs-my06-sti-give-wai/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
×
×
  • Create New...