Jump to content
SAU Community

Fs: Damaged S13

rebound9
 Share

Recommended Posts

rebound9 Apprentice

rebound9

Posted
Posted (edited)

For sale is my damaged S13. Not looking to part out at the moment, hopefully looking to sell as a complete car.

SR20DE

Manual

Gunmetal Grey

Trust shifter kit + short shifter

Trial sideskirts - front bar goneskies and rear bar wasn't supplied when I purchased the car

El Sport Springs

Momo steering wheel

Full 2.5" exhaust system

Car is a Q's model and comes with all the standard Q's features - Digital Climate Control etc.

Point of accident is the driver side corner of the car, will take pictures tomorrow when its brighter. Will need driver side fender, front bar, radiator support and headlight and parker. Engine is in perfect working order and starts no problems.

Good base for a strawberry or onevia conversion or even just to restore.

Looking at 2.5k neg. Will be sold unregistered.

Contact: PM or call 0431 737 515

Located in Liverpool area

Edited by rebound9
Link to comment
https://www.sau.com.au/forums/topic/253709-fs-damaged-s13/
Share on other sites
  • 2 weeks later...
rebound9 Apprentice

rebound9

Posted
  • Author
Posted

Can't seem to edit my original post, but just wanted to add that this car is NOT on REVS, so it's not marked as a repairable write off and can be registered with no major hassles when repaired

Link to comment
https://www.sau.com.au/forums/topic/253709-fs-damaged-s13/#findComment-4406203
Share on other sites
  • 3 weeks later...
rebound9 Apprentice

rebound9

Posted
  • Author
Posted

BUMP

Price drop to 2.2k ono

Car starts everytime no problems. Have purchased a replacement front guard, so all is needed is a new radiator support to line up the panels

Link to comment
https://www.sau.com.au/forums/topic/253709-fs-damaged-s13/#findComment-4445402
Share on other sites
  • 3 weeks later...
rebound9 Apprentice

rebound9

Posted
  • Author
Posted

They are Genuine 2 Piece Enkei Type S racing which I won't be supplying with the sale of the car, unless I get a decent offer for them.

Car is now unregistered and once again be supplied with stockies unless I get a decent offer for the car with rims.

Price drop to 1.6k unrego + stockies.

Link to comment
https://www.sau.com.au/forums/topic/253709-fs-damaged-s13/#findComment-4490035
Share on other sites
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...