Jump to content
SAU Community

Recommended Posts

Hey everybody,

Asus N10JC - 3 months old. Purchased for my holiday in December - But never got to really use it. When used, was plugged in, didn't need the battery, but was plugged in.

Selling, due to requiring a larger one for uni.

24 Months Warranty - Receipts will be included.

Still has all protective cover (See pictures), i have all original paper work, cds, everything unopened.

No scratches, not dents, some slight blemishes on the chrome for some reason (see pics), keys have a bit of use

10.2" Wide Screen

Intel Atom 1.6Ghz

160GB Hard Drive

1GB Ram

**Nvidia 9300M GS 256MB Graphics Card

1.3Mp Webcam

XP Home - I just updated to Service Pack 3

Finger print scanner - I never registered my fingers - protective sheet is over it still

Extras

Purchase for $65 - LowePro 12" Case for it - will give

Samsonite skin - will give

More info can be found here: http://www.asus.com.au/products.aspx?l1=5&...amp;modelmenu=1

Price - $950

Pick up brisbane

Postage can be organised through Aust Post, medium box - $20 or so. + insurance if you want.

Pictures:

th_DSC02097.jpgth_DSC02116.jpg

th_DSC02122.jpgth_DSC02135.jpg

th_DSC02136.jpgth_DSC02137.jpg

th_DSC02138.jpgth_DSC02139.jpg

th_DSC02143.jpg

Edited by Owgasm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...