Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

sorry might have not been clear, i just mean the corner lights, my mate bought a hid kit but he kept the corner lights stock, and it looked weird since he had white bulbs for the headlights while the corner bulb was still yellow, so thats what i mean, here you go have a look at this

http://www.skylinesaustralia.com/forums/R3...;hl=r33+GTR+HID

look at damits post youl know what i mean.

well... personally I would have thought that would be common sense to do the parkers at the same time... but you kept saying "Bright white" as though it was the latest bling fashion or something. I thought you were planning on doing something stupid like blue headlights and white parkers.

LOL , alrite well once i get the car back il go and check out supercheap auto then, also planing on geting windows tinted, just checked out some samples and the darkest legal tint isnt dark at all lol

sif tint..

u need to make bishes watch u at red lights touchin ya junk while ur making eye contact with them..

eg - 610x-222.jpg

Is that charlieeeee murphy....? Or eddie?

Its funkymonkey

err Charlie murphy

:banana:

Hi! skins!! missed u long time brother!

when are we meeting up for more harassment and phantom hands!

Edited by Redsuns88
Its funkymonkey

err Charlie murphy

:blush:

Hi! skins!! missed u long time brother!

when are we meeting up for more harassment and phantom hands!

Name a time and place and im not there

nah... thursday ? I'm on a pinky promise to john :)

pinky promises sound like

dolphin%20unicorn.jpg

make sure u wear your fairy outfit

lol nah ill be there! :blush:

sweet. be good to see ya.

cant wear it, its in the dry cleaners :)

@adam:

You can't put HIDs in the parkers, you want LEDs for them to get the same colour tone (ie white).

Buy full HID kit I assume you mean both high and low beam? This will require two kits, as each kit does 2 bulbs (one per side). You'll struggle to even get two crappy ebay ones for $150.

@adam:

You can't put HIDs in the parkers, you want LEDs for them to get the same colour tone (ie white).

Buy full HID kit I assume you mean both high and low beam? This will require two kits, as each kit does 2 bulbs (one per side). You'll struggle to even get two crappy ebay ones for $150.

hmmm i c, so how much do reckon it would be for the full set? yes im lookin for both high and low beam, i dont mind paying more but i wana buy local somewhere not from ebay unless its an australian store online like justjap etc,

alrite mate, thanks for the help, im gona get the car tinted first, then i might follow the tutorials and clean the headlights up and buy the HID kits needed , the series 3 headlights would be the easier solution but since they retail around 2 grand a set, cant justify that kind of cash, have been lookin around for second hand ones to pop up for quiet a bit, no luck so far,

but thanks anyway,

I good set will be a few hundred PER KIT.

I'm not sure how much the cheap ones go for locally - I got mine ebay styles :blush:

ebay styles are the way to go if you want hids

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...