Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Never got into dexter....... what's it about

Dexter is a serial killer who cleans up all the murderers that the police system can't process because of loopholes in the system (illegal search warrants, tainted evidence, technicalities etc). He works with the police department as a blood spatter analyst and uses his position to get the info on all his victims.

It's quite a good watch, well written, brilliantly cast and keeps you wanting more and more. I slammed through the first two seasons in two and a half nights. Had no sleep and was functioning solely on V and coffee at work, total autopilot.

Season 3 was a one nighter, and Season 4 I just did over the last few days as a couple had to be downloaded again. I was not a patient person while waiting for them to download a second time... there was quite a lot of "The chili cookoff is happening right now! and i'm missing it!" dancing going on.

Worth checking out at least the first season if you've got the time.

BRRRRRRIIIIIIGGGGGGGSSSSSSSNNNNNSSSSSSTTTTTTRRRRRRRRAAAAAAAAAATTTTTTTTTOOOOOONNN

NNNNNN!

FYP

BAHAHAHAHAAHAHAHAHAHA! Imma paint it in John Deere colours and put an SR20DET badge on it

Taken care of :banana:

Dexter...blah blah blah

Hell keen! Sounds like a good show

do it mang! this series is just... chilling :(

And then burn a copy for me!

FYP

Taken care of :banana:

lol

If only you really were joking :(

yer :(

morning bitches

morning, my serbo-croat brother

ATTN: Tristan

Dude, might have a spot for you to play tonight if you're keen. Grand Final, beer at stake.

Not 100% sure yet, but just giving you more than 3 hours notice in case you're available. Let me know :banana:

The dirty sl*t ALWAYS wants to haul a big load. When/Where/Why/How/Who?

Need to take a fridge from Stafford to Aspley.

And Tas made mention of a GTR bonnet I might be able to get - Not sure where that's coming from, but it would also be going to aspley

:banana:

$100 brand new on ebay.

second hand ones tend to break.. If your keen I'll get one spilt postage or something.

Thanks for the offer, but that was more to let her know there wasn't one. I decided I'm not going to bother sourcing vents until I fix the AC. unless I happen to see some for $20 that is.

Once I've got the AC working, I'll replace my center one (I broke it the other day... long story) and buy a passenger one. So if you're still after one then :banana:

I'm sure there's SOMEONE who'd go halves though. You could probably even do a group buy for them! Enough people seem to need them!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...