Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Grrrrrrr can't get damn cat out..... it's held in well with studs + bolts. Got the bolts off but the studs it seems are welded to / are a part of the cat.

Any tips?

Do I have to remove the whole back section of the exhaust to get the cat out? I think I just realised this to be true :P

just work with the wiggle room

exhaust is on hangers, should be able to move it back a bit to get the cat out

its a c*nt of a job on my car, thats why i decided i wasnt going to swap the decat pipe in every track day after doing it once

LOL, found dad's old paperwork for the ride on:

He bought it second hand in 1994, and it was old then:

rideon1.jpg

'twas an 8HP apparently (I thought it was less) but that engine blew up.

He bought the new 10.5HP engine in 1998, at the time it was the biggest one we could get that fit:

rideon2.jpg

I'm not sure how old the mower itself is exactly but I did find the instruction book:

rideon3.jpg

If you look down the bottom, you can note the SIX DIGIT phone number.

Now I remember going from 7 to 8 digits some time in primary school, but 6?

Some quick research, and this very informative page tells me that "Brisbane went to 7 digits in 1975". Therefore, we can conclude that the beast is older than 1975. Thats 35+ years!

And note: it is a mini tractor, not a ride on :P. EEESSSSSSS AAAAAAAAAAAAAARRRRRRRRRRRRRRRRRRRRRRRRR!!!!!!!!!!!!!!!!!!!!!!

Look, you can (could) even get tractor attachments for it:

rideon4.jpg

Definitely needs turbo love

Don't talk to me about ride on trailers, made that mistake once, hung over after new years, we decided to ride in the trailer to clean up the mess we made couldn't find the holding pin to keep it on, going down the hill very fast and the trailer popped off, catapult anyone?

Don't talk to me about ride on trailers, made that mistake once, hung over after new years, we decided to ride in the trailer to clean up the mess we made couldn't find the holding pin to keep it on, going down the hill very fast and the trailer popped off, catapult anyone?

bugger

we could MAKE a trailer for it

matter of fact, there is a small box trailer in the back yard I doubt has any chance of ever getting road registered. Could convert it to a tractor trailer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...