Jump to content
SAU Community

Recommended Posts

Hi guys,

I have a set of good condition Rays Nismo LMGT3.

Wheel specs:

18x9.5 +22 All round

RE01 Tyres 245/40/18

(tyres have about 50%-60% tread life except for front driver side which will need to be replaced)

In Good condition, wheels have some curb rash but can be fixed roughly $50 per wheel. Includes Rays center caps and Original Rays Valvestem caps!!!

These will would look excellent on an R32 or R33 GTR. Reason for the sale is that i have ordered in some 19" wheels to fill the guards on my car.

These wheels are rare to find. 2 Piece forged wheels.

With our crap exchange rate its hard to find any decent wheels. Im after a relatively quick sale. So dont be shy to throw me some offers, please no low balling though. If i dont get a good price then i will just keep them as track rims.

Price: $2200 Negotiable

Pickup: Western Sydney (but can post at buyers cost)

Contact: 0403337740 or PM

wheels.jpg

wheel3.jpg

th_centercap.jpg

rearwheel.jpg

Link to comment
https://www.sau.com.au/forums/topic/262419-rays-nismo-lmgt3-18x95-22/
Share on other sites

id prefer to sell as a complete set. If i sell you this as a pair then it would be difficult for me to sell them.

PM me your budget, im fairly negotiable.

Cheers

  • 2 weeks later...

oh sexy wheels..... *DROOLS* wish i had the money for them i would be at ur place today to pick them up if i had the cash hahahaha... good luck with the sale... free bump for sexy wheels

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...