Jump to content
SAU Community

Recommended Posts

Engine Specs:

N1 24U block (own modifications done) race prepped

Chemically cleaned/crack tested and washed

Torque plate bored honed & decked

All new welsh plugs

Tapped oil gallaries

Fully balanced/detailed crank and grub screwed

Race prepped crank gurdle

Shot peened/prepped standard rods with ARP bolts

Full ARP bottem end stud kit

Ross Racing forged pistons (ceramic coated)

ACL race bearings mains & rods

N1 oil pump (modified)

N1 water pump

Ross harmonic ballancer

Genuine Nissan gasket kit

Fully port & polished head

Match ported intake

Brass valve guids

Standard valves

Upgrade valve springs

Standard cams

Greddy adjustable cam gears

Gates timing belt

Turbo:

New genuine exhaust studs & nuts

Garrett GT3082r turbo polished front cover

Braided oil lines

.82 & 1.06 housings ceramic coated

Tial 44mm wastage

Stainless manifold modified

Exhaust:

4" Stainless dump pipe

4" Stainless catback exhaust

4" Stainless Ballistic hi flow cat

Cooling:

600x300x115mm Greddy style intercooler

Customing aluminium piping

Greddy twin entry air intake pipe

2 x RB25 Air flow meters

Drivtrain:

Custom PBR clutch

Nismo lightened flywheel

Suspension:

Tein Coil overs

Fuel & Ignition:

Nistune ECU

Sard fuel pressure regulator

custom fuel rail

044 fuel pump

2L surg tank

3/8" Aluminium fuel lines

Heap of speed flow fittings & push lock hose

Sard 700cc injectors

Interior:

Series 2 seats front and back

boost guage

electronic boost controller

gtr 11000rpm dash

Exterior:

Genuine gtr front bar

Genuine gtr grill

Top secret carbon bonnet painted

Carbon exhaust shroud

Drift lip

Wheel:

18x8 & 18x9.5 drift r's

Price: $21,000 ono

Contact: pm or call 0435278050 Anthony only serious offers please

Extra info: The car has been finished for around 3 weeks now it starts and runs but will require run in and tune. I have over $25,000 in reciepts plus the cost of the paint job at hand.

img0013hjx.jpg

p1100115.jpg

p1100092.jpg

Edited by johnbarry88
Link to comment
https://www.sau.com.au/forums/topic/265483-rb26-r33-gts-t-street-weapon/
Share on other sites

  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...