Jump to content
SAU Community

Rb25det Fresh Motor

13thracer
 Share

Recommended Posts

13thracer Rising Star

13thracer

Posted
Posted

Complete RB25 DET series 2 motor including all manifolds, turbo and loom. Motor came out a R33 which was crashed, Removed the engine to put into my mates S13 and before fitting to the S13 had the crank cleaned and linished and new main and big end ACL race series bearings fiitted. new gaskets (except head) throughout, timing belt and bearings done. New water pump fitted. Has been in the S13 for a few months now to run the fresh bearings in. Can see running in the car. Engine had done 114,000ks in the skyline and has only done a few thousand more in the Silvia. Motor runs great very smooth fresh motor.

$2300 for the motor Loom and Series 2 turbo

Will separate motor from loom and turbo if need be.

Call Shannon on 0450 052 809

Link to comment
https://www.sau.com.au/forums/topic/265913-rb25det-fresh-motor/
Share on other sites
  • 2 weeks later...
33SXC Apprentice

33SXC

Posted
Posted

Hey Mate

I'm chasing the motor - i don't need the turbo or loom - woudl you be able to seperate? - also you wouldnt of happened to done a compression test on it at all.. would you?

Thanks Heaps :thumbsup:

Em :)

existence Enthusiast

existence

Posted
Posted

hey 33sxc, i went out to have a look at this engine and did a comp test. everything showed up mint the lowest was 159psi and highest was like 167 i think. all in between that

however, i asked if all new gaskets had been put on along with timing belt etc and the owner said no. so i think there has been some communication break down between 13thracer and the owner of the engine !

went for a drive in it, runs flawlessly

he also had recepts for the bottom end work done, so its legit!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...