Jump to content
SAU Community

Recommended Posts

Howdy Guys,

A bit of an update on my progress (ive actually started fixing my car, yay), i have pulled the front bar off my car to fix it, and have found i have lots of rust on intercooler piping and other parts, i am to lasy to take it off myself so i want to sand blast the items. Does anyone know where in caberra to sandblast stuff?

Cheers,

I can't wait to get back on the road with a working car,

Link to comment
https://www.sau.com.au/forums/topic/266210-canberra-sandblasting/
Share on other sites

theres a place just off woolongong street called A1 Sandblasting, its down a VERY bump long driveway out through a metal scrapyard, a few farmer like fellas in a BIG shed, yellow and black sign on top

i got 2 rims done for 60 bucks

I got my whole car sandblasted there, cheap, good work and fast turnaround

AA Sandblasting - 6280 5128

Its an absolute bastard to find though, its across the road from BDL stereo down a long shitty driveway

Theres 2 main forms of sandblasting.

Sandblasting will remove rust but they generally will not use this on panels because the heat produced will distort the panels

Beadblasting is a less abrasive form of sandblasting and will remove paint without creating too much heat or distortion, there will be small amount that may be noticable to the panel beater who picks the car up afterwards.

With my car they sandblasted the engine bay, under panels, wheel wells and door jams then bead blasted the rest. Unless you had huge amounts of rust (eaten away sections of metal) the sandblasting shouldnt punch too much out. If it does though its probably for the best because you'll need it plated anyway.

alex,

how mucd did the enginebay cost to get done?

I have some rust on lower intercooler piping, its surface rust, i jsut want to get rid of it and ill repaint it, there is a couple of braces that i want to get done too, but i wouldnt mind redoing the entire engine bay, depends on cost.

alex

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I thought it could be an issue because the standard plate was flexing when stressed. Maybe the original gear set will hold a bit better without flex? Last time on the dyno it made around 670nm at the hubs. Now it have bigger turbo and better intake but have not been on a dyno yet. The car is being used from family trips to drag race events. So the shifts can be a little violent. It is grinding if I shift to fast so was thinking I should overhaul it soon.
    • From the factory on RB26s there's a fitting on the intake manifold collector/"plenum" that provides pre-throttle boost signal. That's how they did it back in the day, I figure it's fine to replicate it.
    • I would be surprised if that wasn't the issue. It's probably telling you, that even if you remove the plastic liner, you may have some other clearance issues that may occur too in some scenarios. IE, tyre to guard. It looks like someone has already rolled the lip, but you may still have issues in the future IE, turning and hitting a bump etc. The fact it changes how bad it makes the noise when you are going backward vs forward is highly indicative that it's the tyre rubbing. They do make a terrible sound, even if you're only pushing a project car that has a liner hanging down on a tyre!   Has the car been lowered? If it has been, what is the measurement from the centre of the wheel hub to the lip of the guard straight up?
    • Summernats cruiser?
    • Mark's a bit smarter than people give him credit... He'd convince the person that is to become dead, to drive him to the forest first. That way his car has no evidence in it, and he's free to dispose of their vehicle permanently how he sees fit too...
×
×
  • Create New...