Jump to content
SAU Community

Cas

mr 32

By mr 32,
in Engines & Forced Induction

 Share

Recommended Posts

maximajim Community Regular

maximajim

Posted
Posted (edited)

That's the mitsu cas correct? It has the rubber cover on the front. Remove the cover and that is the end of the shaft. I do seem to remember when I removed the two small screws on the shaft itself I was able to remove that portion of the shaft. I think you may be able to remove the remaining 3 screws holding the body to the case and press the shaft out from the back.

Okay I just checked the original cas I dissassembled and as I said you just need to remove three screws and press it out from the back.

Edited by maximajim
Link to comment
https://www.sau.com.au/forums/topic/268832-cas/#findComment-4579823
Share on other sites
mr 32 Grand Master

mr 32

Posted
  • Author
Posted
That's the mitsu cas correct? It has the rubber cover on the front. Remove the cover and that is the end of the shaft. I do seem to remember when I removed the two small screws on the shaft itself I was able to remove that portion of the shaft. I think you may be able to remove the remaining 3 screws holding the body to the case and press the shaft out from the back.

yeah it the mitsu cas,

from what i can see they might not be a way to take it apart without pressing it apart to get to the front housing screws

unless the shaft and bearing comes out when you remove the 3 screws?

Link to comment
https://www.sau.com.au/forums/topic/268832-cas/#findComment-4579850
Share on other sites
mr 32 Grand Master

mr 32

Posted
  • Author
Posted
Is that your cas in the pic?

In that pic all that needs to be done is removing the 3 gold screws holding the body in and then pressing the shaft out from the back. The two screws on the shaft don't need to be removed.

yeah thats it

thats what i thought

thanks for the help

now just to do it without damaging the internals

Link to comment
https://www.sau.com.au/forums/topic/268832-cas/#findComment-4579906
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • MBS206
      NC MX5

      By MBS206 · Posted

      Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Sorry I meant that we are building the EH for a client.
    • The Bogan
      Torana Lx Gtr Hatch, Lots Of Pictures

      By The Bogan · Posted

      LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...