Jump to content
SAU Community

Recommended Posts

Hi guys,

Installed a powerfc and have some problems like some S1 stag's are having, though the pfc should be plug an play (to a degree) with my R34 GTT.

Done some checks and found the following

- Voltage for the throttle motor sensor (pin51) is approx 4.62v.

- Voltage on pin 23 when car is on ignition 0.01 to 0.02 fluctuating,

- Voltage on pin 23 when car is idling is 0.00

- Voltage on pin 37 is 0.00 at ignition and idle

- Voltage on pin 53 is 0.00 at ignition and idle

- Voltage on pin 79 is 0.00 at ignition and idle

I've been told they should be as the following

Pin 23 should be 0.5v approx idling

Pin 37 should be 0.5v approx

Pin 53 should be 4.7v

Pin 79 should be 2v approx

Pin 51 should be 3.4v

symptoms are the following - A/C compressor wont turn on, TCS, SLIP and MIL lights on. powerFC sw sensor check has the THR black background

Im quite lost as to where to look and why so many pins are having no output.

Any idea's where to check?

Link to comment
https://www.sau.com.au/forums/topic/271370-er34-vs-stagea-s1-pinouts/
Share on other sites

Hi guys,

Installed a powerfc and have some problems like some S1 stag's are having, though the pfc should be plug an play (to a degree) with my R34 GTT.

Done some checks and found the following

- Voltage for the throttle motor sensor (pin51) is approx 4.62v.

- Voltage on pin 23 when car is on ignition 0.01 to 0.02 fluctuating,

- Voltage on pin 23 when car is idling is 0.00

- Voltage on pin 37 is 0.00 at ignition and idle

- Voltage on pin 53 is 0.00 at ignition and idle

- Voltage on pin 79 is 0.00 at ignition and idle

I've been told they should be as the following

Pin 23 should be 0.5v approx idling

Pin 37 should be 0.5v approx

Pin 53 should be 4.7v

Pin 79 should be 2v approx

Pin 51 should be 3.4v

symptoms are the following - A/C compressor wont turn on, TCS, SLIP and MIL lights on. powerFC sw sensor check has the THR black background

Im quite lost as to where to look and why so many pins are having no output.

Any idea's where to check?

Series 1 stagea's there are 3 different wiring pinouts/ecu's. I have a series 2 stagea with the neo rb25 and did use a power fc for a while with no problems except for the engine check light which comes on due to no traction control on awd stagea's.

I am a bit unclear to what car/engine combo you have? Is it a stock R34 with the original neo engine, or have you fitted a series 1 stagea engine to it?

Series 1 stagea's there are 3 different wiring pinouts/ecu's. I have a series 2 stagea with the neo rb25 and did use a power fc for a while with no problems except for the engine check light which comes on due to no traction control on awd stagea's.

I am a bit unclear to what car/engine combo you have? Is it a stock R34 with the original neo engine, or have you fitted a series 1 stagea engine to it?

Hey mat,

sorry I should have specified. The car is a R34GTT (ER34) manual with the original neo rb25det. Unfortunately I never had a stock ECU, just an Impul replacement. The impul unit when installed runs fine and no error lights on the dash. a/c TCS can be turned on and off as normal. then switch the loom back to the PFC with the problems as above :)

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...