Jump to content
SAU Community

Recommended Posts

hey guys my dreams got shattered today after trying to fit these onto my r33 gtst after just buying them at the start of this week. fell in love with the look and the rareness of these wheels! the rears were awesome and they stuck out of the guard just a tad just how i liked but the fronts did not fit due to no clearance for the caliper!!!!!!!!

i got these from jms in adelaide and they told me they came off a r33 skyline so i had no problems but they were obviously wrong and i'm not happy at all!!!! :)

i have to sell them now as i don't want to run spacers or anything. offset is unknown as it doesn't mention anything at all on the rim except for manaray, jwl and size. the rears though seem to be around the +30 mark and front within +38 to +30.

if you are interested bring your car around and we'll test fit the fronts on and if they fit they should be o.k. this is considering you dont have a 33 and have small front brakes. have a feeling they could fit on a soarer or fc pretty well. if you have a r32 i am pretty interested to see if they would fit on the front as they mentioned it would fit a skyline but they might have meant r32 and not r33.

*edit* the rears come with screw on/screw off spacers that actually bolt onto the wheel on the back of where the rim sits on the hub. its just under a cm.

specs are:

front 17x8.5 with crap 245/40R17

rear 17x9.5 with crap 245/45R17

the wheels are old but they are in good condition for the age. if you want show rims these arent it. they have a bit of gutter rash, some scratches but overall very good and still shiney condition. they have the centre caps and everything. give them a bit of a clean and they will look great like what they first looked like when jms got them in the picture. (picture is of the actual rims)

want $850ono and i don't want low ballers cause i love these rims. will swap for anything of interest. need these gone asap so i can get some new rims. pick up in western suburbs of vic or will send interstate but at ur own cost. call/msg me on 0432454387

20070605160108.jpg

Edited by jakez88

dude just keep them and run a 15-25mm bolt on spacer, too easy and safe, or even a 5-8mm slip on depending on how far off they are.... or as heaps of people do, file your calipers down a bit, you can take quite a fair bit

i think i might have to run spacers if no one wants to take them off me. gonna have to harden the fk up lol but i'll see how i go with the sale first.

mattysaidso the wheels are at japanese motorsport in adelaide or JMS. the wheels ur after are manaray vr5s but i don't htink they have em anymore.

i'm trying to source out a 20mm bolt on spacer for my fronts and new lug nuts as the standard nuts won't allow me to stick the socket in. clearance is to small. if someone wants them though and for the price i'm asking then i will sell them otherwise my adventure of getting these fitted on the front of my car starts now lol.

pms replied guys. no low ballers please. anyone interested?

i have put the bolt on spacers from the rear to the front and they still dont clear my 33 calipers BUT could most likely clear r32s as there is only a few mm needed to clear. any 32 owners taht are interested and wanting to test fit are welcome.

Edited by jakez88

alrighty these wont fit a r32 as i tried with a friends and didn't fit. need about a 15mm spacer or jsut go 25mm.

measured up as best i could the offset and they seem to be fronts +45 and rears about +38 so definately suitable for a soarer, supra or chaser etc that run high offsets. best to fit up before purchase though.

anyone have a soarer or supra? or if your a hard kunt and wanna run spacers on the front then buy them. $800 guys or throw me an offer.

Edited by jakez88

they wouldn't fit because of the calipers unless you use spacers up front

Edited by jakez88

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...