Jump to content
SAU Community

Recommended Posts

**NEW THREAD**

1996 SUBARU IMPREZA WRX STi Type-RA

140,000KM.......EJ20t.......Manual

Adelaide Hills, SA

$15,000 ono WITH SPARE GEARBOX........OPEN TO SWAPS IF IN SA

This car is currently road registered for every day use but also meets all CAMS requirements for PRC hillclimb track work. Has all the rare Type-RA specs- lightweight panels, aluminium bonnet, extra injector, no electric options to shave weight. The car is mechanically running A1. Oil changed every 5000km. Has new brake pads front and rear. Car comes with a spare gear box worth $1500, the box running right now is absolutly fine, but will chuck the spare it. It also comes with the following stock parts- x4 stock springs, x1 shock good for back or front and stock TMIC. Not exacally sure how much power it is making, these cars are 206KW stock, so add the following on top of that...

* STi Motor, forged pistons, closed deck block

* Close ratio gear box, shot peened

* 3" STi exhaust, dump pipe

* FMIC. black

* Trust TD05 turbo

* Turbo timer

* Uni race chip, [email protected]

* Boost gauge

* King springs, super low

* Cusco strut brace

* K&N pod filter + cold air

* BOV

* Aluminium bonnet

* Nardi steering wheel + gear stick

* Rolled guards

* Cusco roll cage- half in for road reg

* Racing harnesses

* X2 extinguiters

* X4 new tyres (29/04)

post-27567-1244817096_thumb.jpgpost-27567-1244817122_thumb.jpgpost-24-1124842628.jpg

post-27567-1244817214_thumb.jpgpost-27567-1244817249_thumb.jpgpost-24-1124842628.jpg

Contact: 0415 441 980 or PM

post-27567-1244817154_thumb.jpg

post-27567-1244817293_thumb.jpg

Edited by enroe
Link to comment
https://www.sau.com.au/forums/topic/274495-96-wrx-sti-ra/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Sorry I didn’t explain myself properly, by free revving I meant if I just floor it, it gets to 7kish and will start to break up/not hit limiter properly, off boost I’ve driven the car until near on empty. I have a fuel pressure gauge mounted in the engine bay, holds fuel pressure consistently full tank or half tank even when revving, and no the pump sound doesn't change. all the fuel lines inside the tank are fairly new but will look into it, could that also be an issue with the lines outside the tank ?
    • Yeah maybe I got a bad batch that only lasted 6 years. Or conversely maybe I got a good batch that managed to last 6 years.    Either way I have sourced a set of OEM hub/bearing assemblies  so I keep hearing! Even from life long mechanics. Apparently this failure is unheard of…
    • I am trying to understand how that even happened to the hub... wtf
    • Hell, I'm sufficiently wary of the ZSS suspension arms, let alone something like a hub.
    • Got it back home and got started pulling the hub off and diagnose the issue. Axle was stuck after removing the 36mm nut so i used a 3 jaw puller to try and push it out and... eH5FXvJ8.mp4   spend the next few hours trying to remove the axle from the remaining hub as it was very much jammed in there when the spindle sheared off. resulting damage as below R53AIy6 - Imgur.mp4   Looks like the was already a stress fracturing in the spindle as can be seen with the darker cracked section My working theory is maybe when the pinion gear exploded last year the shock put through the hub was the initial crack. Then a few events later it finally let go. Just lucky it happened where it did and not 190km/h on the next sweeper or into the hairpin The bearing/hub assembly went in in 2019 and were non-genuine "ZSS" assemblies and no nails were harmed in the process. #BreakHubsNotNails
×
×
  • Create New...