Jump to content
SAU Community

R32 Tail Lights

BlaznCookie

By BlaznCookie,
in Wanted to Buy

 Share

Recommended Posts

dat2kman Collaborator

dat2kman

Posted
Posted
Looking for R32 Tail Lights... Hoping that GTS-T and GTS-4 both have the same... lights.. but if you have lights for a GTS-4 would be even better.... STOCK, LED whatever... just tail lights for R32. Please PM me with your price.

$120 a pair, in white, complete with globeholders and wiring to plugs

Westside Bris

Link to comment
https://www.sau.com.au/forums/topic/275680-r32-tail-lights/#findComment-4669700
Share on other sites
WHITE R32 Grand Master

WHITE R32

Posted
Posted
what you talking about willis??? GTS-T and GTS-4 are both 2 doors lol... they can come 4 door ya ya... but they are both 2 doors :S

yes but that wasnt stated anywhere above... i was going to say the same thing

Link to comment
https://www.sau.com.au/forums/topic/275680-r32-tail-lights/#findComment-4670767
Share on other sites
  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...