Jump to content
SAU Community

Power Steering Question...

sidewayssam

By sidewayssam,
in General Maintenance

 Share

Recommended Posts

sidewayssam Mentor

sidewayssam

Posted
Posted

Hey guys,

Just wondering with powersteering, is there anyway to get rid of it?

In the last year of drift I have gone through 3 powersteering pumps, I know there probbly is something wrong with the powersteering system somewhere along the lines but I cant really be bothered with it anymore.

I have raced cars before and owned cars without powersteering and I like it beter that way.

So can Powersteering be removed from a RB25 R32?

Cheers

post-45341-1246164534_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/276786-power-steering-question/
Share on other sites
teng Rising Star

teng

Posted
Posted (edited)

If you can't find a skyline with a non power steering option, then the answer is a no.

[off topic]

My friend's toyota corona has a power steering but with a very bad leak. Luckily that same model also had a non power steering option and he found the exact part and bolted it in place. Works like a charm.

Edited by teng

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Hendasto
      Lets play a game - What is causing my oil consumption?

      By Hendasto · Posted

      Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • Hendasto
      Are RBs worth building reliability wise

      By Hendasto · Posted

      At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • MBS206
      New kid on the block

      By MBS206 · Posted

      https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...