Jump to content
SAU Community

Recommended Posts

BLITZ SBC i-D III electronic boost controller - one of the top of the line boost controllers

includes:

Power Meter I-d - RETAILS FOR $298US

2 controllers (ability to set two turbos at different settings on a twin turbo set up,standard kit usually comes with one controller) - $561.60US + CONTROLLER

solenoid (to run turbo they are genuine blitz) - REATILS FOR $270US

wiring there also

One of top of the line from blitz!!!

heaps of functions full specs on the following blitz website

http://www.blitz.com.au/SBCiD.html

was originally purchased for my r31 but have decided to use a link g4 so is not needed as the ecu will control boost.

Its second hand but in mint as condition!!

I'm looking for around $1200 ono to help towards ecu and tuning.

Thanks for the interests.

post-52297-1247574967_thumb.jpg

Edited by Redliner007

Would you be willing to sell 1 only

I already have a Power Meter i-D and an SBC i-D would be a good addition

If you are interested, how much for 1 SBC i-D and 1 solenoid?

Thanks

Would you be willing to sell 1 only

I already have a Power Meter i-D and an SBC i-D would be a good addition

If you are interested, how much for 1 SBC i-D and 1 solenoid?

Thanks

Heya mate, are you able to run the power meter i-d alone with out boost controller? I wasn't aware of this. I would prefer to sell both controllers with the solenoid as it will be no use to me, what are you offering?

Heya mate, are you able to run the power meter i-d alone with out boost controller? I wasn't aware of this. I would prefer to sell both controllers with the solenoid as it will be no use to me, what are you offering?

Yeah the Poewr Meter i-D, just taps into the ecu rev wire i think(cant remember which one, its green and yellow on my car)

And it tells you the power you are making, you can also callibrate the speedo on it, and it will show: speed, power and can make diferent graphs and readings out of them, it also does 0-400m timer and pieces together a dyno graph by the way of your driving, you can also set warnings for speed and power.

But it seems my Power Meter has run into some problems today, it is randomly sounding warnings and showing random power and speed outputs from time to time. I'm thinking its a loose wire. So if i can get it working, i'll still be interested in the SBC.

i think the going rate for a single Blitz i-D SBC is around $350-500, depending on color and if its Spec R or Spec S

As far as i know it is a spec R as that's what i was told when i bought it (are there any physical signs) and on the web Blitz prices are identical for silver and black, it is in U.S dollars? Are you just after 1 controller? If i am able to keep the power meter i-d i will as this was one of the things which attracted me to the set up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...