Jump to content
SAU Community

4sale: Four 19" Adr Chrome Wheels W/ New Tyres [northside Brisbane]


Recommended Posts

As the title suggests, and here are the specs:

19x8.50

5x114.3

+38

These came off my Series 1 R33. And they looked pretty damn nice.

See CHROME ADR-78 Sterling at this link: http://www.adrwheels.com/brand_detail.php?id=chrome&wid=28 These wheels are made in USA and retail for US$300 ea.

The tyres are Marangoni Mythos 245/35 ZR 19s made in Italy, and also retail for AU$300 ea.

I'm no photographer, but hopefully from the photos you can see they are in excellent condition - not even a hint of gutter rash. The tyres are nearly new, again excellent condition.

I am asking for $1200 for the lot. Will consider swap for 16" or 17" rims with new/near new semi-slicks fitted to suit my R33 .

Just send me a PM if you're interested.

wheel1s.jpg

wheel6.jpg

wheel2.jpg

Edited by AASA Racer
  • 1 month later...

Don't need swaps now, just want cash for this wheel and tyre set - $750.00 for all four - that's a bargain, even in this market. All in brand new condition still.

PM Sent

Hey Ivonin, can you please PM me your email address and I'll send the shots through - every time I try to reply via PM to you I get "You cannot send a PM until your post count is higher than 10" and I don't want to post messages just for the sake of building up the tally. Thanks!



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...