Jump to content
SAU Community

Wiring Question R32

helltd

By helltd,
in Engines & Forced Induction

 Share

Recommended Posts

helltd Collaborator

helltd

Posted
Posted

Hey all puttin my 30det into my 32

okay so the cars a 92 gtst rb20det

head is a s1 rb25de

computer is a mapped rb20 to suit

question is-

can I run the rb20det loom? I've already put the rb20 cas and ignitor on so apparently it'll plug in?

Just want to be sure,have the s1 25 loom it had on it but it's been modified too many times,31>31>s13,

so don't wanna use it.

Worse case I get a 25 loom and wire it up,but why bother if the 20 loom will work on the 25de??

Thanks in advance,

Nathan

Link to comment
https://www.sau.com.au/forums/topic/280109-wiring-question-r32/
Share on other sites
James_03 Mentor

James_03

Posted
Posted (edited)

rb20 silvertop loom will work for r32 rb25 non VVT head, providing you use standard injectors etc etc. Intake side sensor wise on both is the same, just your 25 intake ports are bigger on the head itself.

You have said rb25de s1 but, which still came in the R33 with VVT, this will not work.

The head must be a 25 non VVT from an r32, which I am guessing you have to dodge the vvt shit with the 30 bottom end.

Edited by James_03
CEF11E Veteran

CEF11E

Posted
Posted

it will work :blush:

my setup

R32 RB20DET

RB20DET loom, coilpacks, CAS, ignitor, knock sensors, afm, water temp sensor - all running off RB20 computer

RB25DE VCT S1 head, plenum, manifold, vct disabled. TPS, AAC, side feed RB25 injectors

other mods, 800cc injectors Z32afm HX35 turbo external wastegate.

everything runs perfectly, cuttently making 314rwkw and it drives like factory of the remapped RB20 ecu.

pm me if you need any help!

cheers!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...